manualshive.com logo in svg

SEW Movitrac B, Руководство по эксплуатации

Поделиться
Скачать
SEW Movitrac B Скачать руководство пользователя страница 10

10

Operating Instructions – MOVITRAC® B

2

Preliminary information

Safety notes

2

Safety notes

The following basic safety notes must be read carefully to prevent injury to persons and
damage to property. The operator must ensure that the basic safety notes are read and
adhered to. Make sure that persons responsible for the plant and its operation, as well
as persons who work independently on the unit, have read through the operating instruc-
tions carefully and understood them. If you are unclear about any of the information in
this documentation, or if you require further information, please contact SEW-
EURODRIVE.

2.1

Preliminary information

The following safety notes predominantly refer to the use of frequency inverters. Addi-
tionally, when using drives with motors or gearmotors, observe the corresponding safety
notes in the respective operating instructions.

Please also observe the supplementary safety notes in the individual sections of this
publication.

2.2

General information

During operation, frequency inverters can have live, bare parts according to their degree
of protection.

• All work related to transportation, storage, installation, assembly, connection,

startup, maintenance and repair may only be carried out by qualified specialists, in
strict observance of:

– The pertinent detailed operating instructions

– The warning and safety signs on the motor or gearmotor

– All other project planning documents, operating instructions and wiring diagrams

related to the drive

– System-specific regulations and requirements

– The national/regional regulations governing safety and accident prevention

• Never install damaged products.

• Submit a complaint to the shipping company immediately in the event of damage.

Removing covers without authorization, improper use as well as incorrect installation or
operation may result in severe injuries to persons or damage to machinery.

This document includes further information.

Содержание Movitrac B





































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды