SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Скачать руководство пользователя страница 24

Страница: 24 / 80

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card

Engineering interfaces of the DHP11B control card

Project Planning and Startup

This section provides information on project planning for the DHP11B control card and
the PROFIBUS-DP master.

4.1

Engineering interfaces of the DHP11B control card

Connect the DHP11B control card to the engineering PC.

Use one of the following interfaces for configuration access to the DHP11B control card:

•

RS485 (connector X34)

•

CAN 1 (connector X33)

•

CAN 2 (connector X32)

•

PROFIBUS (connector X30)

If the DHP11B control card is to be configured via the USD interface of the engineering
PC, use one of the following adapters:

•

USB/RS485 converter USB11A

•

Commercially available USB CAN dongle (e.g. PCAN-USB adapter supplied by
PEAK-System Technik GmbH)

If the DHP11B control card is to be configured via the PROFIBUS interface, use the C2
Profibus master cards CP5511, CP5611 or CP5512, the "STEP7 V5.3" software and
"SIMATIC Net PB Softnet-DP 6.1" from Siemens AG.

4.2

Connecting the drive inverter via system bus CAN 1 / CAN 2

Connect the DHP11B control card to the MOVIDRIVE

MDX61B drive inverters.

The DHP11B control card is connected to one or more drive inverters via a system bus
(

→

fig. page 15).

Interface X32 (CAN 2) or X33 (CAN 1) is provided for connecting the system bus.

Terminating
resistor

Install a terminating resistor on both ends of the system bus:

•

If a MOVIDRIVE

MDX61B drive inverter (without a DHP11B control card) is con-

nected at one end of the system bus, set its DIP switch S12 to ON.

•

If the DHP11B control card is connected at one end of the system bus, install a ter-
minating resistor of 120

Ω

at the interface to which the system bus is connected (be-

tween pin 2 and pin 3).

Read the installation instructions and information (e.g. for using suitable drivers) in the
MOVITOOLS

MotionStudio software (in the MOVITOOLS

Содержание MOVIDRIVE MOVI-PLC DHP11B

















































































Результаты поиска

Содержание MOVIDRIVE MOVI-PLC DHP11B

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Руководство пользователя

Результаты поиска

Содержание MOVIDRIVE MOVI-PLC DHP11B

Отзывы:

Бренды по названию

Популярные бренды