manualshive.com logo in svg

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Скачать руководство пользователя страница 20

20

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card

3

Operating display of the DHP11B control card

Assembly / Installation Instructions

3.8

Operating display of the DHP11B control card

The DHP11B control card is equipped with seven LEDs that indicate the current status
of the DHP11B control card and its interfaces.

LED 24V / I/O OK

The 24 V / IO OK LED indicates the status of the voltage supply for binary inputs / out-
puts.

PLC status LED

The PLC status LED indicates the firmware status of the DHP11B control card.

20075AXX

LED 24 V / I/O OK

PLC status LED
IEC program status LED
Run Profibus LED
Fault Profibus LED

CAN 2 status LED

CAN 1 status LED

DHP11B

X31

X32

X33

1

3

1

2

3

1

2

3

2

1

2

3

1

2

3

24V / I/O 
OK

Diagnostics

Remedy

Green

•

Voltage supply for the binary inputs/out-
puts is OK.

-

Off

•

Voltage supply is not applied for the 
binary inputs/outputs.

1.

Switch off the drive inverter in which the 
DHP11B control card is installed.

2.

Check and correct the cabling of the 
binary inputs/outputs according to the 
electrical wiring diagram.

3.

Check current consumption of the con-
nected actuators (max. current 

→

 Section 

8).

4.

Switch on the drive inverter in which the 
DHP11B control card is installed.

Orange

Voltage supply for the binary inputs/outputs is 
applied. However, one of the following faults 
has occurred:
•

Overload on one or several binary 
inputs/outputs

•

Overtemperature of the output driver

•

Short circuit in at least one of the binary 
inputs/outputs

PLC sta-
tus

Diagnostics

Remedy

Flash-
ing 
green
(1 Hz)

•

Firmware of the DHP11B control card is 
running correctly.

-

Содержание MOVIDRIVE MOVI-PLC DHP11B

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды