SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B Скачать руководство пользователя страница 64

Страница: 64 / 80

Manual – MOVIDRIVE® MDX61B MOVI-PLC® DHP11B Control Card

Diagnostic procedure for PROFIBUS-DP

Error Diagnostics

7.2

Diagnostic procedure for PROFIBUS-DP

Diagnostic problem: The DHP11B control card does not work on
PROFIBUS.
Initial status:
•

The DHP11B control card is connected physically to PROFIBUS.

•

The DHP11B control card was configured in the DP master and bus
communication is active.

↓

Is the bus connector plugged in?

→

[A]

Yes

↓

Response of the LED Profibus fault?

OFF

→

[B]

→

[C]

FLASHES

↓

The DHP11B control card detects the baud rate but was not configured in
the DP master or was configured incorrectly.

↓

Check whether the configured PROFIBUS address is the same as the
address set on the DIP switches.

↓

PROFIBUS addresses identical?

→

[D]

Yes

↓

You may have configured an incorrect unit type or defined the configuration
incorrectly.

↓

Delete the configuration for the DHP11B control card from the DP network.

↓

Configure the DHP11B control card again, choosing the unit designation
"MOVI-PLC."
Use a predefined configuration to simplify the process. Do not change any
of the preset configuration data!
Assign the address range for your control system.

↓

Load the configuration in the DP master and start the bus communication
again.

[A]

Check the bus cabling!

[B]

The DHP11B control card is currently exchanging data cyclically with the
DP master.

[C]

The DHP11B control card does not detect the baud rate.
Check the bus cabling.

[D]

Adapt the bus addresses.

Содержание MOVIDRIVE MOVI-PLC DHP11B

















































































Результаты поиска

Содержание MOVIDRIVE MOVI-PLC DHP11B

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVIDRIVE MOVI-PLC DHP11B, Руководство пользователя

Результаты поиска

Содержание MOVIDRIVE MOVI-PLC DHP11B

Отзывы:

Бренды по названию

Популярные бренды