manualshive.com logo in svg

SEW-Eurodrive ECDriveS ECIO-8-24-00, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive ECDriveS ECIO-8-24-00 Скачать руководство пользователя страница 9

Safety  notes 

2 

Manual 

– ECDriveS® 

9 

Familiarity with this documentation

In  addition to that, these persons must be familiar with the valid safety regulations and 
laws, as well as with the requirements of the standards, directives, and laws s pecified in 
this documentation. The above-mentioned persons must have the express authoriz ation 
of the company to operate, program, configure, label and ground units, systems and c ir-
cuits in accordance with the standards of safety technology. 

All  work  in  the areas of transportation, storage, operation and waste disposal must be 
carried out by persons who are trained appropriately. These instructions must enable t he 
persons to carry out the required activities and work steps safely and in accordance wit h 
regulations. 

2.4 

Designated use 

The product is intended for installation in electrical systems or machines.  

In case of installation in electrical systems or machines, startup of the product is prohibit -
ed until it is determined that the machine meets the requirements stipulated in t he loc al 
laws  and  directives.  For  Europe,  Machinery Directive 2006/42/EC as well as the EMC 
Directive  2014/30/EU  apply.  Observe  EN  60204-1  (Safety  of  machinery 

–  electrical 

equipment of machines). The product meets the requirements stipulated in the Low V olt-
age Directive 2014/35/EU. 

The standards given in the declaration of conformity apply to the product.  

Technical data and information on the connection conditions are provided on t he name-
plate and in chapter "Technical data" in the documentation. Always comply with the dat a 
and conditions. 

Unintended  or  improper  use  of  the  product  may  result  in severe injury to persons and 
damage to property. 

2.5 

Functional  safety  technology 

If the documentation does not expressly permit it, the product must not perform any safe-
ty functions without supervisory safety systems. 

2.6 

Transport 

Inspect the shipment for damage as soon as you receive the delivery. Inform the shipping 
company immediately about any damage. If the product is damaged, it must  not  be as -
sembled, installed or started up. 

Observe the following notes during transportation: 

Ensure that the product is not subject to mechanical impact during transportation.

Cover  the connectors with the supplied protective caps before transportation.

Only  place  the  product on the cooling fins or on the side without connectors during
transportation.

Always use lifting eyes if available.

If necessary, use suitable, sufficiently dimensioned handling equipment.  

Содержание ECDriveS ECIO-8-24-00












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды