manualshive.com logo in svg

SEW-Eurodrive ECDriveS ECIO-8-24-00, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive ECDriveS ECIO-8-24-00 Скачать руководство пользователя страница 17

Electrical installation 

5 

Manual 

– ECDriveS® 

17 

5 

Electrical installation 

5.1 

Electromagnetic  compatibility  (EMC) 

To  prevent  interference  in  the  ECDriveS®  drive  system  due to EMC influence, always 
route the connection cable of the 24 V control circuit separate from the control cables with 
inductive loads (motors, brakes, contactors etc.) and from supply system cables.  

5.2 

Shielding and routing bus cables 

INFORMATION 

All Ethernet cables for connections between modules are recommended to be shielded.  
Failure to use shielded cables may result in data loss and unexpected result s.  S hown 
above  are Ethernet cables with sealing shrouds required for IP54 compliance. 

5.3 

Installation  instructions 

The nominal voltage of the ECDriveS

®

 control module must correspond to the data for the 

supply voltage. Dimension the cable cross section of the connection cable according t o 
the input current of the imodule (see chapter "Technical data).  

Use the ECDriveS

®

 drive system only in systems that comply with t he requirements of 

protection class 3 according to EN 61140, e.g. SELV. 

At least one of the following means shall provide thermal overload protection of t he c on-
nection lead: 

The maximum output current of the 24 V switched-mode power supply is limited to the
value of the maximum current carrying capacity of the connected conductor.

Fuses in utilization category gG

Type C miniature circuit breaker

5.4 

Grounding of switched-mode  power supply 

According to the requirements for a SELV system, the mass connections  of t he out put  
channels must be connected with the ground potential of the switched-mode power s up-
ply (SMPS) 

[1] Switched-mode power supply

Содержание ECDriveS ECIO-8-24-00












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды