SEPTENTRIO mosaic Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 57

background image

49

49

LED Status Indicators

49

Appendix A

LED Status Indicators

The  LED  pins  can  be  used  to  monitor  the  module  status.  They  can  be  used  to  drive
external  LEDs.    It  is  assumed  that  the  LED  lights  when  the  electrical  level  of  the
corresponding pin is high.

The  general-purpose  LEDs  (GPLED  and  GPLED2  pins)  are  configured  with  the

setLEDMode

command. The default configuration is:

•

GPLED: configured as PVTLED by default;

•

GPLED2: configured as RTKLED by default.

The following LED modes are supported.

GPLED mode LED Behaviour
PVTLED

LED lights when a PVT solution is available.

RTKLED

LED is off if the PVT is not in RTK mode, blinks in float RTK and is solid
on in fixed RTK.

DIFFCORLED

Differential correction indicator. In rover PVT mode, this LED reports
the number of satellites for which differential corrections have been
provided in the last received differential correction message (RTCM
or CMR).

LED behaviour

Number of satellites with corrections

LED is off

No differential correction message received

blinks fast and
continuously (10 times per
second)

0

blinks once, then pauses

1, 2

blinks twice, then pauses

3, 4

blinks 3 times, then pauses  5, 6
blinks 4 times, then pauses  7, 8
blinks 5 times, then pauses  9 or more

The LED is solid ’ON’ when the

module is outputting differential

corrections as a static base station.

TRACKLED

LED behaviour

Number of satellites in tracking

blinks fast and
continuously (10 times per
second)

0

blinks once, then pauses

1, 2

blinks twice, then pauses

3, 4

blinks 3 times, then pauses  5, 6
blinks 4 times, then pauses  7, 8
blinks 5 times, then pauses  9 or more

«
...
47
48
49
50
51
...
»

Содержание mosaic Series


























































Отзывы:

Нет отзывов

Похожие инструкции для mosaic Series

Бренд: Radarcan Страницы: 40

Бренд: BADLANDS Страницы: 2

Бренд: eclisse Страницы: 40

Бренд: LAS Страницы: 6

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Valcom Страницы: 6

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: L-Acoustics Страницы: 20

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Бренд: WAGNER Страницы: 128

Бренд: GEM Страницы: 17

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренд: DUNIWAY Stockroom Страницы: 30

Maestro Wireless Pico Series

Бренд: Lutron Electronics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды