SEPTENTRIO mosaic Series Скачать руководство пользователя страница 3

Страница: 3 / 57

Table of contents

TABLE OF CONTENTS ................................................................................................... 3

DOCUMENT CHANGE LOG .......................................................................................... 7

MOSAIC GNSS MODULE .............................................................................................. 8

3.1

Overview ................................................................................................................... 8

3.2

Mechanical ............................................................................................................. 10

3.3

Absolute Maximum Ratings ................................................................................. 10

3.4

Electrical Characteristics in Operational Conditions ........................................ 11

3.4.1

Power Supply ........................................................................................................ 11

3.4.2

I/O .......................................................................................................................... 11

3.5

Power Consumption .............................................................................................. 12

3.6

Environmental ....................................................................................................... 12

PINOUT AND I/O DESCRIPTION ................................................................................ 13

4.1

Power Supply ......................................................................................................... 14

4.2

Antenna(s) .............................................................................................................. 14

4.2.1

Main Antenna ........................................................................................................ 14

4.2.2

Auxiliary Antenna ................................................................................................. 15

4.2.3

Typical Application ................................................................................................ 16

4.3

COM Ports ............................................................................................................... 17

4.3.1

Typical Application ................................................................................................ 17

4.4

USB Device Interface ............................................................................................. 18

4.4.1

Typical Application ................................................................................................ 18

4.5

Ethernet .................................................................................................................. 19

4.5.1

Typical Application ................................................................................................ 19

4.6

SD Memory Card .................................................................................................... 20

4.6.1

Typical Application ................................................................................................ 21

4.6.2

Data Logging ......................................................................................................... 21

4.7

Clock Frequency Reference .................................................................................. 22

4.7.1

Using the internal TCXO ....................................................................................... 22

4.7.2

Using and external frequency reference ............................................................ 22

Содержание mosaic Series


























































Результаты поиска

Содержание mosaic Series

Отзывы:

Похожие инструкции для mosaic Series

Бренды по названию

Популярные бренды

SEPTENTRIO mosaic Series, Руководство по оборудованию

Результаты поиска

Содержание mosaic Series

Отзывы:

Похожие инструкции для mosaic Series

Бренды по названию

Популярные бренды