SEPTENTRIO mosaic Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 57

background image

12

12

mosaic GNSS Module

12

3.5

Power Consumption

The module is powered through the VDD_3V3 pins, see section 4.1.

The  power  consumption  depends  on  the  set  of  GNSS  signals  enabled  and  on  the
positioning  mode.    The  following  tables  list  the  average  power  consumption  for  some
configurations, while tracking all satellites in view from an open sky, and with the module
at room temperature.  The current is applicable to a supply voltage of 3.3V.

Single-Antenna Modules

GNSS Signals

Positioning
Mode

Power
(mW)

Current
(mA)

GPS L1 C/A

Stand-Alone (1Hz) 550

167

GPS L1/L2

RTK (1Hz)

670

203

GPS/GLONASS L1/L2

RTK (1Hz)

695

211

GPS/GLONASS L1/L2+GALILEO L1/E5a
+BeiDou B1C/B2a (phase 3)

RTK (1Hz)

850

258

GPS/GLONASS L1/L2+GALILEO L1/E5a
+BeiDou B1C/B2a (phase 3)

RTK (100 Hz)

930

282

GPS/GLONASS L1/L2 + L-band

PPP (1Hz)

760

230

All signals from all GNSS constellations

Static (1Hz)

910

276

All signals from all GNSS constellations

+L-band

Static(1Hz)

980

297

All signals from all GNSS constellations

+L-band

Static (100Hz)

1080

327

Dual-Antenna Modules

GNSS Signals

Positioning
Mode

Power
(mW)

Current
(mA)

GPS L1 C/A

RTK+heading (10Hz) 680

206

GPS L1/L2

RTK G +heading
(10Hz)

900

273

All signals from all GNSS constellations

RTK+heading (10Hz) 1060

321

Enabling wideband interference mitigation with the

setWBIMitigation

command adds 70

mW.

Note that the currents given in the above tables are average values. To account for peak
currents, the minimum power supply drive capability should be 500 mA.

3.6

Environmental

Operational: -40 to +85 °C
Storage:

-55 to +85 °C

«
...
10
11
12
13
14
...
»

Содержание mosaic Series


























































Отзывы:

Нет отзывов

Похожие инструкции для mosaic Series

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: FAAC Страницы: 14

Бренд: Haier Страницы: 58

Бренд: ZETRON Страницы: 3

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

Бренд: Lawler Страницы: 5

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

Бренд: Vag Страницы: 12

Бренд: Tech 21 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды