manualshive.com logo in svg

Sensors TOC-625, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sensors TOC-625 Скачать руководство пользователя страница 8

1=FLAMM
10% LEL

á

     0

PASSWORD

â

     0

PASSWORD

á

     0

PASSWORD

áá

   50

PASSWORD

á

    50

PASSWORD

dec
PASSWORD

done
PASSWORD

inc
PASSWORD

cancel
PASSWORD

To access the display press the button for 1-2 seconds

Data entry and menu selection using the password entry as an example.
To access the menu system press the button until the message 
“Release button and enter password”
message is displayed.

Channel
Number

The up arrow indicates
that the indicated password
number will increment at
each button press. 

Gas or Reading
Type

Password Number You are
Entering

Current Channel
Reading

The  back light turns on making 
it easier to see the channel 
information. Note that each 
channel will be displayed in turn 
as indicated 

If the button is pressed twice in a 
short time then two up arrows 
appear to indicate auto increment. 
Now just keeping the button 
pressed increments the reading.

To end Auto Increment mode 
release the button for more than 
1s.

Note auto Increment works in 
menu selection as well as data 
entry to speed up menu 
selections. Make sure auto 
increment is off when making 
selections.

With one arrow displayed 
keep the button pressed 
and the following menu 
options appear.

Release button to select. The arrows 
now indicate down to show you are 
decrementing the number

Release button to select. The arrows 
now indicate up to show you are 
incrementing the number

Release button to select and enter (in 
this case) the password.

Release button to select and cancel 
the action.

Page 8 of 25

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды