manualshive.com logo in svg

Sensors TOC-625, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sensors TOC-625 Скачать руководство пользователя страница 12

With sensors connected and after the TOC-625 controller has completed its warm up the operating 

system will go to normal operation mode.

Normal Operation

In normal operation mode the TOC-625 communicates to each detector or node in turn and displays the 

data on screen. In normal mode the back light will switch off. Pressing the button once will activate the 

back light, each button press then cycles the display through each channel.

For example a three channel system with a Flammable gas detector, a Carbon Monoxide Detector and 

an Oxygen detector would read as:

1=FLAM
0% LEL

2 = CO

0 ppm

3 = O2

21% VOL

Channel Number      Gas Type

Reading         Units

Systems supplied as a complete ‘set’ or order will normally have been set up at the factory during 

final test. A set up report will be supplied with the controller to indicate how the control panel has 

been configured. Where a client advises a particular alarm set up requirement this will be 

incorporated. If no alarm set up is requested then systems will be shipped with alarms at 20% and 

50% of detector range, rising latching alarms, for Oxygen sensors by default alarm 1 will be at 19% 

and alarm 2 at 18% falling non latching alarms. For example the report the three channel discussed 

above would read as follows:

Channel 1

Address
Gas
Range
AL1
AL1 Type
AL1 Relay
AL2
AL2 Type
AL2 Relay
Analogue
Output 
Channel

Channel 2

Address
Gas
Range
AL1
AL1 Type
AL1 Relay
AL2
AL2 Type
AL2 Relay
Analogue
Output 
Channel

Channel 3

Address
Gas
Range
AL1
AL1 Type
AL1 Relay
AL2
AL2 Type
AL2 Relay
Analogue
Output 
Channel

4101
Methane
100% LEL
20%
Rising Latch
1
50%
Rising Latch
2
C1

4102
CO
100 ppm
35
Rising Latch
1
55
Rising Latch
2
C2

4103
Oxygen
25% Vol 
19%
Falling
1
18%
Falling
2
C3

Sales Order: S/36981        Client:  A.N Other                TOC-625 Set Up Report

Supplied Set Up

Page 12 of 25

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды