manualshive.com logo in svg

Sensors TOC-625, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sensors TOC-625 Скачать руководство пользователя страница 13

Channel 1

Address
Gas
Range
AL1
AL1 Type
AL1 Relay
AL2
AL2 Type
AL2 Relay
Analogue
Output 
Channel

4101
Methane
100% LEL
20%
Rising Latch
1
50%
Rising Latch
2
C1

Channel Set Up Overview

The Channel Number as indicated on the TOC-625 display

The gas which this channels detector measures
The measurement range for this channel
The threshold limit for alarm level 1

The threshold limit for alarm level 2

Alarm Action (in this case the alarm latches once the threshold is exceeded

Alarm Action (in this case the alarm latches once the threshold is exceeded

Which relay activates when alarm 1 threshold is exceeded

Which relay activates when alarm 2 threshold is exceeded

Which analogue output relates to this channel.
Note there are three analogue outputs available on the TOC-625

The detector address for this channel. This address will be marked
on the cover of the detector itself

Using channel one as an example the following diagram explains a typical channel set up.

If the control panel has been shipped pre-configured then once correctly connected the system will be 

operational. The controller should correctly cycle through each channel with no indicated errors. 

Relay Test

The alarm relay outputs can now be connected (if they are being used). The relay outputs can be 

forced on and off using the ‘test relay’ function (TEST RLY).

test rly

7 of 9

release

From Normal Operation press the function button until the display 

alters to show ‘release button.

The system now requests a password. Enter 50 to enter the 

Engineer  Menu.

Press the function button until option 7 of 9, TST RLY is displayed. 

Now hold down the button until prompted to release.

The display will now indicate Relay 1 On (and relay 1 should be 

energised. At each press of the button each physical output is 

energised in turn as indicated on the display as:

á

    50

PASSWORD

test rly

7 of 9

tst rly
release

RELAY 1

ON

RELAY 2

ON

BUZZER

ON

LED PWR

ON

LED FLT

ON

LED AL

ON BACK RED

ON

BACK GRN

ON

BACK blu

ON

Each button press cycles through 

the displays as listed. To exit, press 

and hold the button until prompted 

to release

Page 13 of 25

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды