manualshive.com logo in svg

Sensors TOC-625, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sensors TOC-625 Скачать руководство пользователя страница 20

LEVEL

click to

TYPE

click to

SUMMARY

click to

RELAY

click to

EXIT

click to

Once the alarm level has been set you then need to set the Alarm TYPE and decide which relay activates 

once the set alarm level is breached. The following sequence continues from the previous page and 

describes the set up sequences

To select an option press and hold 
the button until prompted to release.

á

L

select 

á

select 

â

select

â

L

select

Bottom line indicates “select alarm type” 
button press moves to the next option

Each 

Rising Latching Alarm

Latching alarms 
remain set until the 
button is pressed to 
reset the alarm. The 
gas level must be 
below the alarm level 
threshold for the reset 
to operate. This type of 
alarm is typically used 
in safety applications. 
Where alarm is 
required in response to 
rising gas levels

Press and hold until 
prompted to release to 
select this option.

Rising  Alarm

Rising alarms will 
automatically reset 
once the gas level falls 
below the alarm 
threshold. This type of 
alarm is typically used 
in control applications 
where action is 
required in response to 
rising gas levels.

Press and hold until 
prompted to release to 
select this option.

Falling Latching Alarm

Latching alarms remain set 
until the button is pressed 
to reset the alarm. For a 
falling alarm the gas level 
must be above the alarm 
level threshold for the reset 
to operate. This type of 
alarm is typically used in 
safety applications for 
Oxygen deficiency 
monitoring where you are 
monitoring for a falling 
Oxygen level.

Press and hold until 
prompted to release to 
select this option.

Falling Alarm

Falling alarms will 
automatically reset once 
the gas level rises 
above the alarm 
threshold. This type of 
alarm is typically used in 
control applications 
where action is required 
in response to falling 
gas level (typical in 
Oxygen deficiency 
applications).

Press and hold until 
prompted to release to 
select this option.

Rising and Falling Non Latching Alarms

Rising and Falling Latching Alarms

Alarm Set Point

Alarm Set Point

Alarm O/P On

Re-Set Input On

Alarm O/P Off

Re-Set Input Off

5% of Alarm Set Point

Alarm Activates

Alarm Activates

10 Seconds

10 Seconds

Alarm Resets

Indicates pressing the front panel ‘jog wheel’ to cancel the alarm

Page 20 of 25

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды