Sensors TOC-625 Скачать руководство пользователя страница 11

Страница: 11 / 33

This Section Follows the Sequence for Putting Into Service to Describe the Menu functions

Figure 1 shows the electrical connections to the Tocsin 625 controller.

Mains power is supplied via connector 2 and should be from a fused spur. This connection should be

made by a qualified electrician.

Cable Checks

Detectors are interfaced to connector 3. It is important to ensure that all connected devices are wired in

accordance with the details supplied in Figure 1 and each relevant detector or I/O node manual.

Cabling should be rigorously checked to ensure there are no cross overs or shorts before any power is

applied. If in doubt follow the cable check procedure listed in “Cable checks T625-700-920.PDF”.

Relay outputs and analogue outputs are indicated on Figure 1, connector 1 and RL1, RL2 respectively.

These should be left unplugged at this stage.

WARMUP

600s

With power applied the system should undertake its power up sequence and

then commence a warm up period. The warm up period is there to allow

connected detectors to stabilise before operation. Note that certain detector

types, Oxygen sensors in particular may take up to 2 hours to fully stabilise.

During the warm up period check that each connected detector or device has power and

communication. The following diagram shows the three main terminal PCB types for detectors and I/O

interface nodes and the relevant check points.

Toc-625
Addressable I/0
Port 3

24V DC

B
A

GND

T106P Pellistor
Flammable Gas
Detectors

T107 Addressable

I/O Node

T102/3 Toxic

IR/Oxygen Comms

Module

ZERO

AUL

CAL

360

CHASS

24V DC

GND

mA+

360

CONC

mA-

Toc-625

Earth Point

Sensor

This LED flashes to
indicate power and
comms. With no
comms LED is on
constantly

Warm Up Period

Page 11 of 25

www.sensors.ltd.uk

A Division of International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Результаты поиска

Содержание TOC-625

Отзывы:

Бренды по названию

Популярные бренды

Sensors TOC-625, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TOC-625

Отзывы:

Бренды по названию

Популярные бренды