manualshive.com logo in svg

Sensors TOC-625, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sensors TOC-625 Скачать руководство пользователя страница 30

Additional Menu’s for Gas Metering. 

The   VIEW ALL   Menu

If the controller is configured as a TOC-630 then additional menu’s are available to interrogate and test the 
unit.

reading=3.350m3

1 of 15

VIEW ALL

4 of 9

gas supply=1

2 of 15

tel no 2=+44753531001

5 of 15

account number=0100

7 of 15

gas detection=0

3 of 15

tel no 3=+44753531002

6 of 15

tel no 1=+44753531000

4 of 15

SERIAL NUMBER=GXF223454

8 of 15

INITIAL READING=0.050

9 of 15

INITIAL READING DATE=11.10.2010

10 of 15

This menu provides information only. Each button press displays the next data item. To adjust any of these 
parameters requires access to IGD configurator software. In each case the top line of the display scrolls to 
display the data.

Indicates current stored meter reading

Indicates the initial gas meter reading on installation.

Indicates current status of the gas supply,
1=Gas Solenoid On, 0=Gas Solenoid Off

Indicates current status of the gas detection,
1=Gas Detected, 0=Normal, no gas detected

This is the client account number and must match the account 
number stored on the host PC running IGD TOC 630 
communicator software.

This is the serial number of the gas meter on site.

Indicates the stored external 
telephone numbers that the TOC-
630 will accept commands from. 
One of these numbers must be the 
host PC system which remotely 
collects data. The remaining two 
numbers can be used for example 
for remote engineer diagnostics 
etc.

Indicates the date of the initial meter reading.

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды