Sensors TOC-625 Скачать руководство пользователя страница 10

Страница: 10 / 33

It is recommended to follow the set up sequence below when configuring and installing a control
panel from new.

Follow the cable commissioning procedure T625-700-920.PDF
if you don't have a copy of this download it from www.sensors.ltd.uk

Perform a sensor FIND and automatically install detector data. Engineers Menu .... Find Option

(note panels are usually supplied pre-configured so this
many not be necessary, check shipping documentation)

Set the sensor channel alarm levels. User menu ... Alarm Setup Options AL1 and AL2 for each
channel.

(note panels are usually supplied pre-configured so this
many not be necessary, check shipping documentation)

Allow the system to run for at least a few hours then:

Zero each connected detector. User Menu ZERO

Calibrate each detector. User Menu CALibrate

EXIT to normal operation and check alarm operation by applying calibration gas and observing
alarm activation.

Make sure all components are communicating correctly. Engineers menu TEST ADD option.

find

1 of 9

alarm 1

3 of 8

alarm 2

4 of 8

zero

1 of 8

cal

2 of 8

test add

3 of 9

Putting Into Service

Note that this product should be supplied via a fused spur. Ensure cables used are suitable for both
their intended area of operation and load capability. This product should only be installed by a
competent person.

Page 10 of 25

www.sensors.ltd.uk

A Division of International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Содержание TOC-625


































Результаты поиска

Содержание TOC-625

Отзывы:

Бренды по названию

Популярные бренды

Sensors TOC-625, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TOC-625

Отзывы:

Бренды по названию

Популярные бренды