SEI Insta-Berm Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 47

background image

Section 4: Installation

Installation Procedures

2018 Insta-Berm (Frame) Operations Manual

(Version D)

10

We Engineer Solutions

Section 4: Installation

Installation Procedures

Selecting a Site

The frame-supported Insta-Berm system may be installed on asphalt, concrete, sand or soil if the surface is
well groomed and level. The site selected must be free of rocks, sticks and other debris that may damage
the floor of the berm.

Select a site approximately 6’ (1.8m) larger in each direction then the overall berm size (see

Section 7:

Specifications and Parts

for overall dimensions). For best operating conditions, the slope of the site selected

should not exceed one degree in any direction. Any slope will reduce the capacity of the berm. However,
if the site has a slope in only one direction, it can result in better draining of the berm.

Preparing the Site

The surface of the ground should be smooth and firm. If the berm is to be installed on a paved surface, the
surface should be swept clean before installation. Sharp gravel on top of a hard surface may puncture the
berm.

Select a site (maximum slope one degree).

1.0

Important Note

SEI recommends consulting a soils engineer to determine soil composition. A soils engineer can
also determine if the soil is stable enough to support the weight of the berm and any objects inside
the berm.

«
...
12
13
14
15
16
...
»

Содержание Insta-Berm
















































Отзывы:

Нет отзывов

Похожие инструкции для Insta-Berm

Бренд: D-Link Страницы: 24

DCS-3110 - SECURICAM Fixed Network Camera

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 18

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 17

Бренд: V-TAC Страницы: 97

Бренд: V-TAC Страницы: 14

Бренд: Zircon Страницы: 2

Бренд: DAITEM Страницы: 22

Бренд: Datavideo Страницы: 136

Бренд: i3 International Страницы: 42

GigE uEye SE Rev. 4

Бренд: IDS Страницы: 27

Бренд: Kaya Instruments Страницы: 49

Бренд: NookBox Страницы: 7

Бренд: Varex Imaging Страницы: 60

AD-200 Main Unit

Бренд: Datavideo Страницы: 14

DH-IPC-HUM4231S-L5

Бренд: Dahua Technology Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды