background image

Section 8: Warranty  

2018 Insta-Berm (Frame) Operations Manual 

(Version D)

 

   43

We Engineer Solutions

Section 8: Warranty

a) Warranty is limited to repairing or replacing, at the company’s sole discretion, any product approved to
be defective.

b) The company’s products are not guaranteed for any specific length of time or measure of service, but are
warranted only to be free from defects in workmanship and material for a period of one year to the original
purchaser.

c) To the extent allowable under applicable law, the company’s liability for consequential, incidental and
environmental damages is expressly disclaimed.  

The company’s liability in all events is limited to and

shall not exceed, the purchase price paid.

d)  This  warranty  is  granted  to  the  original  purchaser  and  does  not  extend  to  a  subsequent  purchaser  or
assignee.

e) The company must receive notification in writing of any claims of warranty from the original purchaser
which must give details of the claimed defect in the product.

f) Where the original purchaser is claiming under warranty, the product must be returned to the company for
inspection with all transportation and duty charges prepaid.

g)  The  warranty  does  not  extend  to  any  product  that  has  been  accidentally  damaged,  abraded,  altered,
punctured, abused, misused or used for a purpose which has not been approved by the company.

h) This warranty does not apply to any accessories used with the product such as pumps, filters, hoses, etc.,
that are not supplied by the company, and any warranty on such accessories must be requested from the
manufacturer or dealer of the accessories.

i) In the event the original purchaser does not give notice of a warranty claim within one year of the original
purchase  of  the  product,  it  is  understood  that  the  purchaser  has  waived  the  claim  for  warranty  and  the
purchaser and/or any subsequent purchaser must accept the condition of the product as it may be, without
warranty.

j) Any technical information supplied by the company regarding the product is not a condition of warranty
but rather is information provided by the company to the best of its knowledge.

k) There are no implied warranties nor is there any warranty that can be assumed from any representation
of any person, except the company itself.

Exclusions

This  warranty  is  void  if  the  product  is  not  assembled,  used  and/or  maintained  in  accordance  with  the
operator’s manual supplied by SEI.

Содержание Insta-Berm
















































Отзывы: