sebaKMT HL 7000 Скачать руководство пользователя страница 35

Страница: 35 / 74

Performing measurements

5.1.3

Display

The information in this section refers to the standard level measurement display.
If the description does not match the display on your device, in the system
settings, check which display details are actually enabled (see page 38).

The display area contains the following information:

Element Description

Minimum level

Lowest noise level of the current measurement.

Minimum frequency

Frequency of the quietest sound of the current measurement.

Minimum level

(as bar graph)

The length of the bar indicates the lowest level of the current measurement.
The colour of the bar represents the frequency of the sound.

blue

yellow

0 Hz

4000 Hz

Instantaneous value

Current level as a bar and numeric value.

Maximum level

The red vertical line shows the highest level of the last 10 seconds.

Frequency spectrum

The white curve represents the frequency spectrum.
The red curve represents the set frequency filter.

Содержание HL 7000











































































Результаты поиска

Содержание HL 7000

Отзывы:

Похожие инструкции для HL 7000

Бренды по названию

Популярные бренды

sebaKMT HL 7000, Руководство пользователя

Результаты поиска

Содержание HL 7000

Отзывы:

Похожие инструкции для HL 7000

Бренды по названию

Популярные бренды