SDLG LG968 Скачать руководство пользователя

Страница: 9 / 117

Operation & Maintenance Manual

──

LG968 /969Wheel Loader

△

WARNING

The wrong operation, maintenance and repair could results in

hurt and death.

Operator should read this manual carefully before operation or maintenance.

Never

involve in operation and maintenance and repair of the machine before reading and

understanding this manual.

The operation specifications and precautions given in the manual only apply to intended

uses of the machine. If the machine is used for any unintended conditions that are not

specifically prohibited, be sure that operation will not induce hurts to you and other

persons.

No operation and action is allowed that is conflict with the description in the manual.

Содержание LG968






















































































































Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды

SDLG LG968, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды