SDLG LG968 Скачать руководство пользователя

Страница: 61 / 117

Operation & Maintenance Manual

──

LG968 /969Wheel Loader

Speed Gauge

This gauge shows the speed during machine driving.

Indicator Lamp

See “

1.1 General View of Controls and Gauges Figure3-3 Figure3-2

” in this

chapter.

Pre-heat Indicator Lamp:

The lamp will be on if start switch is turned to preheat position when

machine equipped with cold boot equipment; the lamp will be off if start switch is turned to other

position.

Oil Pressure Alarm Lamp Turning Switch:

The lamp will be on if the oil pressure is below

0.1MPa.

Charging Indicator Lamp:

The lamp will be on if start switch is turned on. It will be off

immediately after the engine is started. Otherwise it means there is some problem with storage battery,

please examine and repair.

Power Cut Off Indicator Lamp:

Power is cut off if the lamp is on; power is not cut off if the

lamp is off.

Step on the left brake pedal, the power is cut off, lamp is on; step on right brake pedal, power is

not cut off, lamp is off.

Emergency Turn Indicator Lamp:

if the emergency turn indicator lamp is assembled, if the

emergency pump works, the lam will be on if the machine turn in emergency.

Содержание LG968






















































































































Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды

SDLG LG968, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды