SDLG LG968 Скачать руководство пользователя

Страница: 89 / 117

Operation & Maintenance Manual

──

LG968 /969Wheel Loader

Park the machine on plane ground, put the transmission lever at

neutral

(“

”) position, push the

parking brake switch, and wedge the front tire. Rotate to open the oil inlet plug on the shells of

front and rear axle. It is proper if the oil level is at the bottom side of oil inlet, otherwise please

add axle oil. Please watch 5 minutes after adding oil, if the oil level keeps stable; please rotate to

assemble the oil plug. Selections of axle oil please see “

CHAPTER IV 2.2

Selection of

Oil, Fuel and Coolant

”.

②

Oil Replacing

Park the machine on plane ground, run the engine 10 minutes, use small accelerograph to move

the machine slowly to let the oil drain plug of front axle at wheel side at the lowest position

Shut engine, put transmission lever at

neutral

(“

”) position, push the parking brake switch,

wedge the front and rear wheels.

Rotate to disassemble the oil drain plugs of two wheels near front axle and the oil drain plugs at

the bottom of axle shell bottom to release oil to container.

△

WARNING

The temperature of axle oil may be high please wear protective

clothes, and operate carefully to prevent self hurt.

Release all the old oil and rotate to assemble the oil drain plugs at the bottom of axle shell

bottom.

Start engine, rotate the parking brake switch gently until it rebounds, use small accelerograph to

move the machine slowly to let the oil drain plug of front axle at horizontal position, and then

shut the engine, put the transmission lever at

neutral

position, push down the braking control

switch.

Add new axle oil (about 32 L) from the oil drain port of two wheels near front axle and the oil

inlet port at the middle of axle shell. And then check the oil level again.

Содержание LG968






















































































































Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды

SDLG LG968, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды