SDLG LG968 Скачать руководство пользователя

Страница: 87 / 117

Operation & Maintenance Manual

──

LG968 /969Wheel Loader

3.6.2 Adding Fuel to Fuel Tank

Fuel Level Checking

Park the machine on plane ground, check the fuel level from

outside of fuel tank. If the fuel level is under 0, please add fuel

from inlet of fuel tank. Fuel selection please see

“

CHAPTER IV 2.2 Selection of Oil, Fuel and

Coolant

”.

3.6.3 Adding Oil to Gearbox

①

Oil Level Checking

Park the machine on plane ground, put the transmission lever at

neutral

(“

”) position, push the

parking brake switch, and wedge the front

tire.

Start engine, run the engine at idle status (at

about 1000r/min), rotate to loose the oil

dipstick of oil inlet at the left side of gearbox,

stretch it out and clean.

Dip the oil dipstick into oil pipe and rotate tightly, and then take out (at least twice).

Oil temperature is about 40

℃

, oil level should between lower scale and middle scale.

Oil temperature is about 80

℃

, oil level should between upper scale and middle scale.

If the oil level is not at the prescriptive scale, please add prescriptive hydraulic transmission oil.

Selection of hydraulic transmission oil please see “

CHAPTER IV 2.2 Selection of Oil,

Fuel and Coolant

”.

②

Oil Replacing

Park the machine on plane ground, put the transmission lever

neutral

(“

”) position, push the parking brake switch,

and wedge the front tire.

Make sure the gearbox at the working temperature,

rotate

Содержание LG968






















































































































Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды

SDLG LG968, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LG968

Отзывы:

Похожие инструкции для LG968

Бренды по названию

Популярные бренды