background image

 
 Assembly and Operating Manual 
 
AGE-F-XY 

– Compensation Unit with spring return 

 
 

11 

Date printed 28.12.2009 

7.2  Disassembling 

 

Warning! 

Before assembling or disassembling of the unit, the power supply must be switched off.

 

 Please also consider the safety hints on page 4. 

 
 
 
 

The Pos. Numbers refer to the assembly drawing (see Chapter 8, page 12)

 

1.  Separate the module from the handling device. 
2.  Separate the cable connections. 
3.  Loosen the set screws (item 51) on the lower part of the housing (item 1). 
4.  Remove the screws (item 30) on the lower part of the housing (item 1). 

 

 

Note! 

The outer guide rails and the respective roller cages of the linear guide  
(item 20) fall off after the lower part of the housing (item 1) has been lifted. 

5.  Lift the lower part of the housing (item 1) carefully off of the module. 
6.  Loosen the set screws (item 51) on the upper part of the housing (item 2). 
7.  Remove the screws (item 30) on the upper part of the housing (item 2). 

 

 

Note! 

The outer guide rails and the respective roller cages of the linear guide (item 20) fall off 
after the upper part of the housing (item 2) has been lifted. 

8.  Lift the upper part of the housing (item 2) carefully off of the guide cross (item 3). 
9.  Remove the screws (item 5) to separate the linear guide (item 20) from the guide 

cross (item 3). 
 

 

Warning! 

The return springs (item 15) are installed under bias. 

10. Remove the set screws (item 50) from the guide cross (item 3)  

to get to the return springs (item 15). 

11. Take the guide sleeves (item 4) out of the guide cross (item 3). 

 

 

Note! 

The cylindrical pins (item 40) are glued in firmly and must not be removed  
since they are carefully aligned and are responsible for a precise repeat accuracy. 

12.  Clean all parts thoroughly and check all parts for any defects and wear. 
13. To mount the linear guides (item 20), use the grease mentioned in chapter 7.1 

 

 

Note! 

During assembly make sure the set screws (item 51) are not tightened too tightly, or 
else there is a danger of jamming the unit. 

14. Assembly takes place in the opposite order. 

 
 

Содержание AGE-F-XY




















Отзывы: