Schmidt PressControl 3000 Скачать руководство пользователя | Manualshive

Страница: 23 / 56

background image

5 Data Input

SCHMIDT

®

PressControl 3000 – V1.3

23

No. Parameter

Description

25 idle-stroke monitoring

This parameter defines whether the “idle-stroke monitoring” function is active or not (0=active,
1=inactive)

26

max.force idle-stroke

If the “idle-stroke monitoring” function is active, this parameter defines the maximum allowed force
which must not be reached.

27

stroke for idle-stroke

If the “idle-stroke monitoring” function is active, this parameter defines the stroke which has be
controlled.

30 PC on/off

This parameter defines whether the control unit has to be connected to an external PC for
operation.

31

SPC on/off

This parameter determines whether the "SPC " has been switched on or not (0=off, 1=on).

40

Move tolerance on/off

This parameter defines whether the “Offset of tolerance data” function is active or not (0=active,
1=inactive)

41

Ref-pos. stroketol.1

This parameter defines the intersection of the reference curve with the stroke tolerance 1.

42

Force tare on/off

The "Force tare" function is used to tare the force value after each stroke to the value "0".

45

Part check on/off

This parameter defines whether a part is available on an optionally mounted workpiece fixture or
not (0=active, 1=inactive)

47 ACK n.ok-box on/off

This parameter defines whether a part has fallen into an optionally mounted reject box or not
(0=active, 1=inactive).

50

Bend up [mm/kN]

The measured bending constant eliminates the elastic properties of the overall system.

51

BDC signal (I1.3) exist.

This parameter defines whether the press is provided with a cylinder switch or not (0=not provided,
1=provided)

52

TDC signal (I1.4) exist.

dto

54

Sensor type

Enter the sensor type (5 kN, 20 kN, 100 kN or 160 kN) according to the activated press type.

55

Adm offsetdrift pos.

The allowed offset drift is set by default to 50 increments. If the value of the force measuring
system exceeds the nominal value or drops below it by 50 increments when the control unit is
switched on, the error message “Error force measuring system” appears on the display. This error
message indicates a possible defect of the force measuring system (e. g. sensor deformed). The
force measuring system should be immediately checked and calibrated again!

56

Adm offsetdrift neg.

dto.

57

Aq. distance PDA force

The “increment” of the process data acquisition determines the frequency of the written measuring
points (standard value 5 inc., i.e., every 5 increments one measuring point). The larger the value,
the fewer measuring points are written.

58

Aq. distance PDA stroke

dto.

59

Offset stroke

The “Offset stroke” value is machine specific. The measured value for the activated machine is
included in the test certificate.

«
...
21
22
23
24
25
...
»

Содержание PressControl 3000

























































Отзывы:

Нет отзывов

Похожие инструкции для PressControl 3000

Бренд: S&C Страницы: 40

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 168

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 29

Бренд: Panasonic Страницы: 37

Бренд: Panasonic Страницы: 9

Бренд: BADODOSECURITY Страницы: 8

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Dahua Страницы: 58

Бренд: Gate Motors Страницы: 6

Бренд: tams elektronik Страницы: 12

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды