manualshive.com logo in svg

Schmidt PressControl 3000, Руководство оператора


Поделиться
Скачать
background image

11 Maintenance and servicing 

SCHMIDT

®

 PressControl 3000 – V1.3 

52

 

 

Figure 11-2: Amplifier board 

1 

Potentiometer for the force offset 

 

 

2 

Potentiometer for the amplification 

 

 

 

If you turn the screw on the potentiometer, but the value in the “Offset force” 
does not change: 

  Switch the control unit off. 

  Switch the control unit on again. 

  Try again to set the force offset. 

 

11.2  Calibrating the force sensor 

Since the force measuring system is usually used for measuring quality-
relevant specifications, it should be inspected and, if necessary, calibrated at 
reasonable intervals established by the user. As specified by the DIN EN 
ISO 9000, a calibration of the system must be carried out at regular 
intervals. 

The calibration is also offered by SCHMIDT Technology as part of its 
customer service. 

 
A reference measuring system is needed for the calibrating of the force 
measuring system. A calibration value is calculated using the measured 
value of the reference measuring system and the measured value of the 
machine. 

SCHMIDT Technology optionally offers the SCHMIDT

®

 LoadCheck 

reference measuring system for the calibration of your system. 

 

  Select the "Data Output" system function key. 

  Press the "Data Output" system function key again to display the "Data 

Output 2". 

  Place the force sensor of the reference measuring system beneath the 

ram. 

 

  Subject the force sensor to the nominal pressing force. 

  Read the reference measured value on the display module (display in 

kN) and the measured value of the press system.  

1 

2 

Prerequisite 

Preparing press system 

Recording 

measured values 

Содержание PressControl 3000

























































Отзывы:

Нет отзывов

Похожие инструкции для PressControl 3000

Ubisys J1 Manual preview
J1
Бренд: Ubisys Страницы: 2
Balboa Instruments EL Series Hot Sheet preview
EL Series
Бренд: Balboa Instruments Страницы: 10
Quantum Data 980 Application Manual preview
980
Бренд: Quantum Data Страницы: 36
C&K systems Securit 800L Specfications preview
Securit 800L
Бренд: C&K systems Страницы: 2
Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Бренд: Warren Controls Страницы: 16
2VV AirGENIO SUPERIOR Manual preview
AirGENIO SUPERIOR
Бренд: 2VV Страницы: 27
YOKOGAWA CX1000 Installation And Connection Manual preview
CX1000
Бренд: YOKOGAWA Страницы: 2
Halma ALICAT SCIENTIFIC PC Quick Start Manual preview
ALICAT SCIENTIFIC PC
Бренд: Halma Страницы: 2
Halma ALICAT SCIENTIFIC PCD Operating Manual preview
ALICAT SCIENTIFIC PCD
Бренд: Halma Страницы: 46
Harman Kardon OMNI 10 Quick Start Manual preview
OMNI 10
Бренд: Harman Kardon Страницы: 25
Uniss SR601 Operation Instructions Manual preview
SR601
Бренд: Uniss Страницы: 21
Kathrein CAP Converter Operating Instructions Manual preview
CAP Converter
Бренд: Kathrein Страницы: 16
S&P RMB Quick Start Manual preview
RMB
Бренд: S&P Страницы: 17
S&S Northern Merlin 1000VW+ Installation, Operating And Maintenance preview
Merlin 1000VW+
Бренд: S&S Northern Страницы: 9
IBM 1L Maintenance Information preview
1L
Бренд: IBM Страницы: 20
DAV TECH DA 600 Installation And Maintenance Manual preview
DA 600
Бренд: DAV TECH Страницы: 24
OBSIDIAN CONTROL SYSTEMS NX2 Installation Manual preview
NX2
Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16
IBCcontrol MicroMax180 Manual preview
MicroMax180
Бренд: IBCcontrol Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды