Schmidt PressControl 3000 Скачать руководство пользователя

Страница: 12 / 56

3 Assembly and startup

SCHMIDT

PressControl 3000 – V1.3

3.2 Connecting the control unit

The back of the control unit housing contains the following connections:

Figure 3-1: Connections

not used (only ManualPress)

5 Inputs/outputs

2 Supply

voltage

6 Service

3 Force/stroke

sensors

7 USB

4 CAN

Damage to the force/stroke sensors

The cables may only be connected in the de-energized state. This applies
especially to the connection of the force/stroke sensors.

Connect the control unit in the order described below.

The communication between the control unit and the press or the
force/stroke sensors takes place via two connections.

Connect the control unit to the press using the cable for the force/stroke

sensors (12-pin plug).

Connect the control unit to the SafetyModule using the CAN-cable (5-

pin plug).

Connect the control unit to the 24V power supply of the SafetyModule.

3.3 Installing the control unit

The control unit is equipped ex works with a control unit holder for table or
wall mounting.

Insert the control unit in the table holder.

Tighten the fastening screw (1).

CAUTION

Communication

Power supply

Содержание PressControl 3000

























































Результаты поиска

Содержание PressControl 3000

Отзывы:

Похожие инструкции для PressControl 3000

Бренды по названию

Популярные бренды

Schmidt PressControl 3000, Руководство оператора

Результаты поиска

Содержание PressControl 3000

Отзывы:

Похожие инструкции для PressControl 3000

Бренды по названию

Популярные бренды