Schmidt DTX Скачать руководство пользователя страница 39

Страница: 39 / 44

17.10.2016 12:29

DTX-Series 1000 cN

Unit cN

Material: CU 0.25-0.4mm

Start: 11:38:09 17.10.16

Start: 11:39:10 17.10.16

Start: 11:40:12 17.10.16

Stop: 11:38:17 17.10.16

Stop: 11:39:18 17.10.16

Stop: 11:40:20 17.10.16

Last: 237

Last: 221

Last: 239

Avg: 236

Avg: 234

Avg: 235

Max: 246

Max: 243

Max: 245

Min: 216

Min: 217

Min: 214

std.dev.: 125

std.dev.: 115

std.dev.: 120

MAXPeak: 570

MAXPeak: 544

MAXPeak: 564

MINPeak: 40

MINPeak: 44

MINPeak: 40

HI-Alarm: 850

Lo-Alarm: 150

Records: 8000

374

229

385

410

206

382

438

190

399

461

189

410

478

215

430

489

278

454

497

355

466

498

415

466

492

441

467

3.7.4.3 Displaying the saved measured values on a PC

The SCHMIDT software

Tension-Inspect 3

is supplied with the tension meter. It

allows you to easily and accurately analyze the saved measured values and export
them to an Excel table.

Sample memory printout

3.7.3.4 Deleting the saved measured values

If data is saved in the tension meter, the display shows “Mem” and indicates the free
memory space.

Deleting data:

- Press the „Recall“ and buttons
- Then press the

button and confirm with the

button.

This clears the memory.

Содержание DTX













































Результаты поиска

Содержание DTX

Отзывы:

Похожие инструкции для DTX

Бренды по названию

Популярные бренды

Schmidt DTX, Руководство пользователя

Результаты поиска

Содержание DTX

Отзывы:

Похожие инструкции для DTX

Бренды по названию

Популярные бренды