Schmidt DTX Скачать руководство пользователя страница 8

Страница: 8 / 44

V-grooved

Line Speed

max. m/min

Roller Material

Standard

2000

Hard-coated aluminium

Standard

4000

Hardened steel

only for DTXL

Code

3500

Hard-coated aluminium

Code

5000

Plasma-coated aluminium

Code

1000

Plastic (POM) black

Code

4000

Plastic (PVC) red

only for DTXF

Code

1000

Nickel-plated steel

Code

1000

Hardened steel

Code

1000

Tempered steel for

measuring tire cord

Code

CE2

1000

ceramic-coated aluminium

Asymetrical groove

Code

ASY

1000

Hard-coated aluminium

(not for DTX-200)

Code

ASYB

1000

Tempered steel for

measuring tire cord

(not for DTX-200)

Code

1000

Hard-coated aluminium

(only for DTX-60K-V1)

U-grooved

Code

2000

Hard-coated aluminium

(not for DTX-200)

Code

4000

Hard chrome-plated steel (radius R5)

only for DTXL

Guide Rollers:

2.1 Specifications

(cont.)

Signal processing:

16 bit A/D

Temperature coefficient:

Gain:

less than

0.01 % full scale* /°C at 25° C

Zero point: better than

0.3 % full scale* /°C at 25° C

Temperature range:

10 - 45° C

Air humidity:

85 % RH, max.

Power supply:

LiPo Accumulatoru (approx. 40 h continuous use,

charging time approx. 3 1/2 h),

AC adapter 100 - 240 V AC, adapter (EU, USA, UK)

Housing material:

Die-cast aluminium

Housing dimensions:

265 mm x 78.5 mm x 46 mm (L x W x H)

Weight:

Up to DTX-50K approx. 875 g / 1550 g

(net / gross)

DTX-60K-V1 approx. 1040 g / 2700 g

The requirements of the CE specification are only complied with if the

tension meter is equipped and operated with equipment supplied by HANS

SCHMIDT & Co GmbH. Certification to the CE specification does not extend

to, and shall be invalid for any other combination. For damage resulting the-

reby we assume no liability.

2.2 Connecting the tension meter

Содержание DTX













































Результаты поиска

Содержание DTX

Отзывы:

Похожие инструкции для DTX

Бренды по названию

Популярные бренды

Schmidt DTX, Руководство пользователя

Результаты поиска

Содержание DTX

Отзывы:

Похожие инструкции для DTX

Бренды по названию

Популярные бренды