schmalenberger FLUVO F Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 52

background image

37

Pump NB/FB/WP/SM/F
Version: 27216 - E

Schmalenberger GmbH + Co. KG

D-72072 Tübingen / Germany

When using glass container. (up to manf. year 2008): Version 1

TLS. safe operation

To ensure safe operation, the catchment chamber must always be filled with a sufficient
quantity of clean sealing fluid. The sealing fluid must exhibit good compatibility with the
pumping medium. The slight overpressure in the catchment chamber of up to 0.5 bar is
normal and serves as additional protection against the GLRD (mechanical seal) running
dry.
The external temperature of the catchment chamber must not exceed 70°C in normal
operation and must never exceed the boiling temperature of the sealing fluid. We
recommend monitoring the temperature and level of the sealing fluid. The medium being
sealed off must be in a liquid state against the GLRD (mechanical seal) of the SKS
(catchment chamber system) in every operating state.
If the stated operating limit data are observed and the instructions given in the manual are
followed, the SKS (catchment chamber system) should operate with no problems.

Fig. 9:

Glass container

The minimum and maximum filling levels
are marked on the viewing glass. The
level of the sealing medium may increase
while the pump is in operation due to
heat. If the level is too high, the sealing
fluid may flow out. However, that will not
affect the functionality of the SKS.
To simplify filling the catchment
chamber, an oil gun can be ordered from
SCHMALENBERGER under item
number 54199.

«
...
35
36
37
38
39
...
»

Содержание FLUVO F





















































Отзывы:

Нет отзывов

Похожие инструкции для FLUVO F

Бренд: Eagle Страницы: 16

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: YAMADA Страницы: 14

iSOLAR PDP Series

Бренд: ICON Страницы: 24

ZHHS-01-10K-R290-V5-M

Бренд: JBG HT Страницы: 32

Бренд: Underhill Страницы: 2

Бренд: GE Страницы: 1

FLEXFLO A-100NE

Бренд: Blue-White Страницы: 28

Бренд: Energie Страницы: 31

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

Бренд: Metabo Страницы: 77

Бренд: hajdu Страницы: 72

LARIUS SIRIO 60:1

Бренд: Samoa Страницы: 46

SINGLE PACKAGE DUAL FUEL HEAT PUMP

Бренд: York Страницы: 8

Бренд: FE PETRO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды