schmalenberger FLUVO F Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

background image

11

Pump NB/FB/WP/SM/F
Version: 27216 - E

Schmalenberger GmbH + Co. KG

D-72072 Tübingen / Germany

2.3

Setting Up and Connecting

2.3.1

Before starting to set up, check the following

•

Is the machine / system / container connection prepared according to the dimensions
of the dimension sheet / installation diagram?

•

Do the concrete foundations have sufficient concrete strength (min. B 15) per
DIN 1045?

•

Is the concrete foundation hardened?

•

Is the surface horizontal and even?

2.3.2

Installation and Set-up of the Pump

Except for the special design, pumps are always placed on a base plate with the pump,
bracket or motor mount and fastened with bolts.
For assembly on a foundation, the centrifugal pump must be aligned with a spirit level.

Pump with angle base

For installation on a foundation, the unit must be aligned using a spirit level on the pressure
connection.

Installation on motor mounts

Alignment as for angle base. For certain motor sizes, the motor mounts must be supported
underneath (see installation diagram).

Check to ensure the pump is running easily and freely before starting assembly
Other external accessories such as air chambers, etc., that are not
premounted on the pump in the factory should not be connected until after the
pump is installed in the system or on the pump foundation.

Explosion protection / safety instructions

Electrical equipment that will be operated in areas subject to the risk of
explosion must meet explosion protection requirements. These are identified
by the factory plate on the motor. For installation in areas subject to the danger
of explosion, applicable local regulations for explosion protection and
requirements of the test certificate included with delivery, which was issued by
the office responsible for testing, must be observed. The test certificate
included with delivery must be kept in a safe place at the installation location
(for example in the supervisor's office, etc.).

Stability - risk of injury!

Pump with large drives that are installed vertically are top-heavy. These pumps
must be secured against tipping during assembly or disassembly, for example
by using retaining ropes.

Caution!

Never install the pump with the
„motor below“.

«
...
9
10
11
12
13
...
»

Содержание FLUVO F





















































Отзывы:

Нет отзывов

Похожие инструкции для FLUVO F

Бренд: Balcrank Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: Kaisai Страницы: 40

Water Jet Lightning

Бренд: Oase Страницы: 28

AquaMax Eco Premium 4000

Бренд: Oase Страницы: 120

Бренд: Oase Страницы: 9

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

Бренд: Samoa Страницы: 40

Бренд: Edwards Страницы: 16

Бренд: York Страницы: 178

Бренд: T.I.P. Страницы: 117

Бренд: habitat et jardin Страницы: 19

Бренд: TOHATSU Страницы: 99

Бренд: Eco-Flo Страницы: 18

Бренд: BA Pumps & Sprayers Страницы: 18

Бренд: hajdu Страницы: 65

Бренд: Danfoss Страницы: 68

Бренд: WACKER Group Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды