manualshive.com logo in svg

schmalenberger FLUVO F, Руководство оператора и инструкции по установке

Поделиться
Скачать
schmalenberger FLUVO F Скачать руководство пользователя страница 34

   

 

34                                                                                          

Pump NB/FB/WP/SM/F

Version: 27216 - E

Schmalenberger GmbH + Co. KG 

D-72072 Tübingen / Germany

7.3

Improper Use

Operation outside of the conditions listed in section 7.2 "Usage Limits" is not permitted.
Before operating the SKS under other conditions or at a different location, please consult
with SCHMALENBERGER to determine whether there are any concerns.

7.4

Description of the Product

SKS (catchment chamber system) requires a sealing medium to retain proper function.
The purpose of the sealing medium is to divert heat that is generated and to prevent the
medium being sealed off (on the pump side) to a great extent from entering into the sealing
gap. The sealing medium completely fills up the space between the product and
atmosphere-side GLRD. 

7.5

System with sealing pressure (SK)

Commissioning and safe operation

In this SKS (catchment chamber system) the arrangement of the GLRD (mechanical seal)
is "Back to Back". The function of this double-action GLRD is only ensured if the catchment
chamber is completely filled with clean sealing medium.

Fig. 7 

Caution!

Before commissioning the pump unit, make certain the catchment chamber is
filled with clean sealing medium. 

Caution!

The pump unit was delivered with the catchment chamber empty. Due to the
factory approval, however, the inside surfaces of the catchment chamber are
wetted with oil. If the sealing medium is not compatible with mineral oil, the
catchment chamber should be rinsed with a solvent before filling.

Содержание FLUVO F





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды