Scheppach 5645 0901, Руководство пользователя

Страница: 17 / 45

12 english
Fig. 08.1
In case of deviations adjust as follows.
• Loosen sixfold screws (1)
• Align slit wedge vertically
• Slightly tighten sixfold screws (1)
• Align the slit wedge to the saw blade and tighten the
sixfold screws (1) again.
Longitudinal end stop, Fig. 09
Screw the middle plate onto the end stop pipe. Do not
tighten!
2 flat edge screws M6 x 50
2 discs ø 6
2 wing nuts M6
Slide in end stop rail and wedge.
Position 1 = high installation surface
Position 2 = low installation surface
Put the longitudinal end stop in the clamping appliance.
Clamp = pull clamping flap up
Unfasten = push clamping flap down
Electrical connection
The installed electrical motor is connected ready to operate.
The connection complies with the relevant VDE- and DIN-
regulations.
The power supply as well as the used extension cable
should comply with these regulations.
Motor-brake facility
Your construction circular saw is equipped with an
automatically functioning deadlock brake. The brake starts
functioning after switching off the motor.
Important information
The electrical motor is made for operating mode S 6 / 40
% .
When the motor gets overcharged, it automatically switches
off. After a short cool-down period (time varies) the motor
can be switched on again.
Defective electrical power supply cords
Electrical power supply cords often suffer insolation
damages. Causes are:
• Pressure spots, when power supply cords are being led
through windows or doors.
• Buckling spots by incorrect attachment or guidance of
the power supply cords.
•Cuttings by driving over a power supply cord.
•Insulation damages through pulling out of the socket.
•Cracks in worn­out insulation.
Such defective electrical power supply cords should not be
used and are extremely dangerous because of the insulation
damage.
Check electrical power supply cords for damages on a
regular basis. Please observe that upon checking the power
supply cord is not plugged in. Electrical power supply
cords have to comply with the relevant VDE - and DIN-
regulations. Only use power cables with the qualification H
07 RN. An imprint of the type denomination is rule.
Alternating current motor, Page U5
• The supply voltage should be 230 Volt/50 Hz.
• Extension cables must be up to 25 m long, have a cross
cut of 1.5 square millimeter, be over 25 m long, and
have a minimum 2.5 square millimeter.
• The powersupply should be 16 A.
Rotary current motor, Page U5
• The power supply should be 400 Volt/50 Hz.
• The power supply and the extension cables must be 5­
fold leads = 3 P + N + SL.
• Extension cables must have a minimum cable cross
section of 1.5 square millimeter.
• The power supply should be maximum 16 A.
• In case of connection to the power supply or moving site
the rotary direction should be checked, otherwise the
polarity has to be changed (wall mounted connector).
Therefore screw the phase switcher into the plug
surrounding with a screw driver. (See Fig. 10)
Connections and repairs of the electrical equipment should
only be carried out by an electrical specialist.
In case you have further questions, please specify the
following:
•Motor manufacturer
•Current type of the motor
•Information of the machine type label
•Information of the switch type label
When sending back the motor, always return the complete
power unit with switch.
Implementation
Please read the safety information before implementation.
The implementation of the machine is only admissable
when protection and safety facilites have been installed
completely.
Put the machine on a stable, even floor. If necessary attach
through the bottom through the holes to the frame valves.
(screws/nails)
After connection to the power supply your scheppach
construction circular saw is ready to operate.