manualshive.com logo in svg

Schacht Wolf Pup, Руководство по сборке


Поделиться
Скачать
background image

- 8 -

rear castle 

cross brace

front castle 

cross brace

Figure 12 - iNSTALL THe CArriAge BOLTS

1/4" washers 

and lock nuts

1/4 x 7

"

      

carriage bolts

12. 

Install the treadle aid and rear castle cross brace 

and carriage bolts. 

Parts: Rear castle cross brace, treadle aid,  2 -- 2" screws,  
2 – 1-1/2" screws,  2 – 1/4" x 7" carriage bolts, 2 – 1/4" lock 
nuts 
 
Using the 2 1-1/2" screws in the upper holes at each end, 
attach the rear castle cross brace to the castle.  Using the 2 
2-1/2" screws, attach the treadle aid to the castle through 
the two bottom holes in the rear castle cross brace. (Figure 
11-C) 
 
Push the jacks down in the center and insert the carriage 
bolts through the holes in the front castle cross brace and 
on through the holes in the rear castle cross braces. Align 
the square part of the carriage bolts in the square holes 
and tap them firmly into the holes. Put a 1/4" washer on 
each bolt and secure with a 1/4" lock nut. Do not tighten 
the lock nut all the way.; the washer should remain loose.

Figure 11 - iNSTALL THe JACK AND LAMM ASSeMBLieS, reAr CASTLe 
CrOSS, AND TreADLe AiD

jack pivot rods

back side of front 

castle cross brace

two 3/8" 

washers on 

each rod

A

#1 jack assembly

one 3/8" washer 

on each rod

B

#1 jack assembly

#3 jack assembly
#4 jack assembly

treadle aid

rear castle 

cross brace

#2 jack assembly

C

11. 

Install the jacks and lamms.  

Parts: 2 – jack pivot rods, 22 –  3/8" SAE washers, 2 – #1 
jack assemblies, 2 – #2 jack assemblies, 2 – #3 jack assem-
blies, 2 – #4 jack assemblies.    

 

From the rear of the loom, insert the two aluminum jack 
pivot rods into the larger holes of the front castle cross 
brace. Place two 3/8" washers on each of the rods. (Figure 
11-A) 
 
Place a #1 jack assembly on the rods. Place a 3/8" wash-
er on each rod, followed by a second #1 jack assembly. 
Continue in the following order: a washer on each rod, a 
#2 jack assembly, a washer, the second #2 jack assembly, 
and a washer. Continue with a #3 jack assembly, washers, 
the second #3 jack assembly, washers, a #4 jack assembly, 
washers, and the second #4 jack assembly.  Finish by plac-
ing two 3/8" washers on each rod. (Figure 11-B & 11-C)

Содержание Wolf Pup














Отзывы:

Нет отзывов

Похожие инструкции для Wolf Pup

Ashford FOOT CONTROLLER Instructions preview
FOOT CONTROLLER
Бренд: Ashford Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды