manualshive.com logo in svg

Schacht Wolf Pup, Руководство по сборке


Поделиться
Скачать
background image

- 11 -

20. 

Install the brake eyebolt and brake spring. 

 

Parts: 1 – eyebolt, 1 – brake spring, 1 – 3/16" washer 
 
Attach the brake spring to the brake bar. Insert the eye-
bolt through a 3/16" washer, through the hole in the long 
barrel nut, and screw it into the spring.

Tighten the eyebolt until you can’t turn the warp beam 
away from you when you twist the beam with both hands. 
When you hold the brake release pedal down, the warp 
beam should turn freely in either direction. 

By tightening or loosening the eye bolt, you can increase or 
decrease the tension on the friction brake. There should be 
small gaps between the coils of the brake spring once the 
proper tension is reached. 

Figure 20 - iNSTALL THe BrAKe eYeBOLT AND BrAKe SPriNg

brake 

spring

brake 

eyebolt

washer

brake bar

Figure 21 - iNSTALL BrAKe BeAM CrANK HANDLe

21. 

Install the warp beam crank handle. 

Parts: 1 – warp beam crank handle, 1 – 3/8" washer,  
1 – 3/8" cap nut. 
 
Place the 3/8" washer and then the metal crank handle 
on the threaded shaft extending through the leg from the 
brake end of the warp beam. The wood crank handle faces 
away from the loom. Secure with the 3/8" cap nut. Tighten 
the nut by placing the handle over it and turning clockwise. 
To engage the crank for turning the warp beam, pull the 
hexagonal hole in the crank onto the cap nut. While weav-
ing, the crank should be pushed off the cap nut.

cap nut

warp beam 

crank handle

3/8" washer

threaded  

shaft

22. 

Install the removable back beam. 

 

Parts: Back beam, 2 – black knobs, 2 – fender washers, 2 – 
1/4" barrel nuts. 
 
Slide the back beam into the slots cut in the top of the 
inside legs. Put a fender washer on a knob, and insert the 
knob through the leg, into the back beam, and tighten it 
into a barrel nut in the back beam. Repeat for the other 
side.

Inside 

left leg

back beam

fender 

washer

black knob

barrel nut

Figure 22 - iNSTALL THe reMOVABLe BACK BeAM

brake bar

Figure 19 - iNSTALL THe BrAKe COrD

S-hook

19. 

Install the brake cord. 

 

Parts: 1 – brake peg, 1 – S-hook, Texsolv brake cord.  
 
Remove the shrink wrap packaging holding the brake 
release pedal to the outside right leg, being careful not to 
let it slam to the floor.  Attach the S-hook to the hole on the 
rear of the brake bar. Loop the Texsolv brake cord through 
the S-hook on the brake bar. Slip the other end of the cord 
through the hole in the brake release pedal. Secure the 
brake cord by inserting the brake peg into the 4th loop 
from the end of the Texsolv brake cord. 

brake 

release 

pedal

Texsolv 

brake cord

Texsolv 

brake cord

brake 

peg

Содержание Wolf Pup














Отзывы:

Нет отзывов

Похожие инструкции для Wolf Pup

Бренды по названию

Популярные бренды

Загрузить еще бренды