Sanyo VDC-HD300P Скачать руководство пользователя

Страница: 60 / 116

Click

CODEC/STREAMING

in the configuration menu to display the CODEC/STREAMING SETTINGS screen.

Configure the conditions of the video/image transmission.

Configuring Aspect Ratio

Configuring JPEG images

Configuring H.264 video

Required operation privilege: admin, operator

If [SSL] is set to “ON” on the NETWORK SETTINGS screen, you cannot configure H.264 video.

In [ASPECT RATIO], select the aspect ratio (width-to-height ratio) of the video/image by
clicking the corresponding radio button and click

SET

16:9 (Landscape), 4:3 (Portrait)

Clicking

SET

reboots the camera.

Configure the resolution (RESOLUTION).

The available options vary depending on your selection in [ASPECT RATIO].

16:9

: 1920×1080, 1280×720, 1024×576, 640×360

4:3

: 2288×1712, 1600×1200, 1280×960, 1024×768, 800×600, 640×480, 320×240

Configure the image quality (PICTURE QUALITY).

BASIC, NORMAL, ENHANCED, FINE, SUPER FINE

Configure the live video frame rate (LIVE FRAME RATE) for each operation privilege and

click

SET

The available options vary depending on the model used.

VDC-HD3300/VDC-HD3100: 0.1ips, 0.2ips, 0.5ips, 1ips, 3ips, 5ips, 10ips, 15ips, 30ips

VDC-HD3300P/VDC-HD3100P: 0.1ips, 0.2ips, 0.5ips, 1ips, 2.5ips, 5ips, 8ips, 12.5ips, 25ips

Working with Administrator Configuration Screens 12/50

Содержание VDC-HD300P





















































































































Результаты поиска

Содержание VDC-HD300P

Отзывы:

Похожие инструкции для VDC-HD300P

Бренды по названию

Популярные бренды

Sanyo VDC-HD300P, Руководство пользователя

Результаты поиска

Содержание VDC-HD300P

Отзывы:

Похожие инструкции для VDC-HD300P

Бренды по названию

Популярные бренды