Sanyo SPW-C0705DZH8, Технические данные инструкция

Страница: 61 / 703

3-9
Control of 3-WAY ECO-i SYSTEM
1
2
3
4
5
6
7
8
2. Wireless Remote Controller
Operating Multiple In/Outdoor Units Simultaneously
Using the Remote Control
For Best Results
Addresses
Group control works well for providing air conditioning to one, large room
with more than one air conditioning units.
One remote control can operate up to eight indoor units.
All the indoor units have identical settings.
Set temperature sensing to the indoor unit (Main Sensor).
(Group Control)
Indoor Unit
Indoor Unit
Signal Line
Receiver
Wireless Remote Control
Point the transmitter of the remote control at the receiver. When the signal is received correctly it will beep once.
(It beeps twice only when the unit starts operating.)
The signal can be received at a distance of about 6 meters. This distance should be used only as a guide. It depends on
battery strength.
Make sure nothing is between the remote control and the receiver that could block the signal.
Do not leave the remote in direct sunlight, where the wind from the air conditioner can blow directly on it, or near any other
heat source.
Take care not to drop, throw or wash the remote control with water.
The signal from the remote control may not be received in rooms with rapid start fluorescent lighting, inverter lights, plasma
displays, LCD televisions (monitor), etc. For more information, please contact the dealer where the product was purchased.
Wall Mount Use
•
•
Press from the location you wish to mount the remote and make sure the signal is
received correctly.
Pull the remote control forward to remove it.
Don’t get the remote control too far away from the receiver.
This may cause a malfunction.
Be sure to keep the remote control in the same room as the receiver.
Point the remote control at the receiver.
When the signal is received correctly it will beep one time.
Avoid locating the remote control where it is covered, such as behind a curtain.
Keep it out in the open.
1
2
Fasten the remote
control mount with
screws. Fitting the remote
control in the
mount.
Remote control
mount
Press
Put in
In both multi and single unit installations, when more than one indoor unit is installed in the same room with a compatible
remote control, addresses can be set up to avoid crosstalk.By setting the address switches on the receivers and matching
them with the number of addresses on the remote control, up to six indoor units can be controlled separately with the remote
control. (When using units in a flexible combination or operating multiple units simultaneously, as they are operated at the
same time, they cannot be controlled individually.) There are separate address settings, receiver addresses for the receivers*
1
and transmitter addresses for the remote control.
For more information, please contact the dealer where the product was purchased.
• The setting procedure is different for Indoor Unit (K type). (See Setting Addresses (K Type) in the next page.)
• These settings are saved in nonvolatile memory in the remote control, so even when its batteries are changed, the settings
do not have to be made again.
*1 RCS-SH80BG.WL and RCS-TRP80BG.WL are of receivers (Inside the indoor unit); RCS-SS80BG.WL is of an operation
panel. (Inside the indoor unit)
Checking Addresses
When you press on the remote control, its current address is shown in the display. If this address corresponds to the
address of a receiver
*
2
, the buzzer sounds. (If it is on ALL, the buzzer will always sound.)
If it is on ALL, it can be operated regardless of receiver addresses. Point the remote control at the receiver you wish to operate
and transmit.
*2
RCS-SS80BG.WL is a receiver. (Indoor unit)
Matching up Addresses
Setting Remote Control Addresses
1. If you press and at the same time , “ ” will blink.
2. While holding down, every time you press , it cycles from ALL 1 2 3…
Set it to the receiver address switch of the indoor unit you wish to operate.
3. When you release , the address that was displayed is set.
When you do this, if it corresponds to the receiver’s address setting, the buzzer sounds.
6 ALL.
1-7.
1-8.
1-9.
1-10.
TD831143-00̲W-3WAY.indb 9 TD831143-00̲W-3WAY.indb 9 2008/12/01 10:26:22 2008/12/01 10:26:22