Sanyo SPW-C0705DZH8, Технические данные инструкция

Страница: 59 / 703

3-7
Control of 3-WAY ECO-i SYSTEM
1
2
3
4
5
6
7
8
2. Wireless Remote Controller
1. Remove the cover.
2. Insert two AAA alkaline batteries.
Put the batteries in with the polarity [+/–] as shown in the figure.
3. Gently insert one end of an unfolded paper clip (or a similar object that can
fit) into the Reset hole and press the Reset button inside the hole and then
put the cover back on.
Change the batteries when the display of the remote control gets weak or if it will
not work unless close to the receiver. (Alkaline batteries generally last about one year.)
When changing batteries, always use two fresh batteries of the same make.
If the remote control will not be used for a long period of time, remove the batteries.
Please dispose of batteries appropriately.
After changing the batteries, follow the procedures described below to reset the current time.
Reset hole
Cover
After changing the batteries and pressing reset, be sure to reset the current time.
(When reset is pressed, the current time reverts to
[ ])
1.
2.
3.
4.
Press for two seconds or more.
Once the clock displays starts blinking, the clock can be set.
Set the hour with / of the .
If you press and hold the button, the time changes quickly.
Set the minutes with
/
of the
.
If you press and hold the button, the time changes quickly.
Pressing completes the time setting.
While you are setting the current time, the time display flashes but the colon does not.
If the buttons are not pressed for three minutes while setting the current time,
it is set to the displayed time.
When reset is pressed, the timer settings are deleted.
2 1,4 3
Power: Turn on the power of the indoor unit at least 14 hours before operation.
1.
Press
.
2. Press and select from among Auto
, Heat , Dry ,Cool and Fan
.
3. Press and select the desired speed.
If set to Auto
(Auto does not work when in the Fan mode.) , the fan speed switches automatically.
4. Press one of the buttons and set the desired temperature.
Temperature settings cannot be made when in the Fan mode.
MAX MIN
Auto 27 17
Heat
30 16
Dry / Cool 30 18
Stop: Press
.
When the unit is stopped with the remote control, even though the compressor of the
outdoor unit stops, the fan on the outdoor unit may continue to run for a while.
Auto ,Heat ,Dry , Cool
, Fan
Models that only provide the cooling function cannot operate in the auto or heating modes.
1
4
2
3
If the unit is not heating very effectively with a Low fan speed , switch the fan speed to High
or Medium.
Depending on the indoor unit being used, it may indicate a function that it does not have. (The fan speed is set.)
If you cannot turn the air conditioner off in the normal way.
Disconnect the power to the indoor unit and contact the dealer where the product was purchased.
<Auto Operation>
If all the indoor units are identical in a cooling system and are under control as one group, it heats or cools automatically via
the differences between the set temperature and the room temperature.
<Dry Operation>
Depending on the indoor unit used, the remote control may have a [Dry] indicator on its display
even though the unit does not have the Dry function. (Same as cooler operation)
When the room temperature approaches the temperature setting, the unit continues to start up or stop automatically.
When the drying mode stops operating, the indoor unit’s fan blows a gentle breeze in order to keep the moisture from returning
to the room at a minimum.
Depending on the indoor unit used, and/or the temperature in the room, the fan speed may not be adjustable.
Depending on the unit used, when the outside air temperature is 15 °C or less, the dry function will not operate.
1-2. Installing Batteries
1-3. Setting the Current Time
1- 4. Operation
NOTE
NOTE
TD831143-00̲W-3WAY.indb 7 TD831143-00̲W-3WAY.indb 7 2008/12/01 10:26:21 2008/12/01 10:26:21