Sanyo SPW-C0705DZH8, Технические данные инструкция

Страница: 13 / 703

Calculation of the indoor air-conditioning load
Selection of an air conditioning system
Design of the control system
Calculation of the corrected outdoor unit capacity
•
Design of tubing
1-2. Procedure for Selecting Models and Calculating Capacity
Model Selection Procedure
Select the model and calculate the capacity for each refrigerant system according to the procedure shown below.
Design a suitable control system for the selected air conditioning system.
Preliminary selection of indoor and outdoor units
Make preliminary selections that are within the allowable range for the system. ............ 2-4 ~ 2-10
Check of the tubing length and elevation difference
Check that the length of refrigerant tubing and the elevation difference are within the allowable
ranges. ....................................................................................................................................... 2-4
Capacity correction coefficient for model. .................................................................... 2-11, 13, 14
Capacity correction coefficient for outdoor temperature conditions. .................................. 2-11, 13
Capacity correction coefficient for tubing length and elevation difference. ........................ 2-11, 14
Heating capacity correction coefficient for frosting/defrosting. ........................................... 2-11, 13
Capacity correction coefficient for indoor temperature conditions. .................................... 2-11, 14
Capacity distribution ratio based on the tubing length and elevation difference. ............... 2-11, 14
Calculation of the actual capacity for each indoor unit
Calculation of the corrected capacity for each indoor unit
Calculate the corrected indoor/outdoor capacity ratio, based on the corrected outdoor unit
capacity and the total corrected capacity of all indoor units in the same system. Use the result
to calculate the capacity correction coefficient for the indoor units. ............................. 2-11 ~ 2-14
Multiply the corrected capacity of each indoor unit by the capacity correction coefficient to
calculate the actual capacity for each indoor unit. ................................................................... 2-12
If the capacity is inadequate, reexamine the unit combinations.
Recheck of the actual capacity for each indoor unit
Example 1: Increasing the outdoor unit capacity. .................................................................... 2-18
Example 2: Increasing the indoor unit capacity. ...................................................................... 2-19
Increasing the tubing size. ....................................................................................................... 2-20
Create a tubing design which minimizes the amount of additional refrigerant charge as much
as possible. ...................................................................................................................... 2-4 ~ 2-6
If tubing extension is expected in the future, create the tubing design with adequate considera-
tion for this extension.
Select the tubing size for the main tube (LA) up to the No. 1 distribution joint based on the rated
cooling capacity of the outdoor unit. Select tubing sizes after the distribution point based on the
total rated cooling capacity of the connected indoor units.
Increasing the tubing size of the wide tubes can reduce the loss of capacity caused by longer
tubing lengths. (Only the main wide tube with the largest tube diameter (main tube LA and main
tubes after the distribution point that are the same size as LA) can be changed.) In this case,
it is necessary to recalculate the actual indoor unit capacities. ................................................ 2-20
Calculation of additional refrigerant charge amount
Calculate the additional refrigerant charge from the diameters and lengths of the refrigerant tub-
ing. Even if the wide tubing diameter was increased, determine the additional refrigerant charge
based only on the narrow tubing size. ...................................................................................... 2-21
Check the minimum indoor capacity (limit density) with respect to the amount of refrigerant. If the
limit density is exceeded, be sure to install ventilation equipment or take other corrective steps. .. 2-22
Design of electrical wiring capacity
Select a wiring capacity according to the method of power supply. ......................................... 2-24
Calculate the maximum air-conditioning load for each room or zone.
Select the ideal air conditioning system for air conditioning of each room or zone.
2-3
Design of 3-WAY ECO-i SYSTEM
1
2
3
4
5
6
7
8
1. Model Selecting and Capacity Calculator
TD831143-00̲W-3WAY.indb 3 TD831143-00̲W-3WAY.indb 3 2008/12/01 16:15:40 2008/12/01 16:15:40