Sanwa mg5000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

Sanwa mg5000 Скачать руководство пользователя страница 19

− 16 −

6-2 Calibration

The calibration and inspection may be conducted by the dealer.

For more information, please contact the dealer.

6-3 Cleaning and Storage

1. The main unit is not resistant to volatile solvent and must

not be cleaned with lacquer thinner or alcohol. If it gets

dirty, wipe lightly with a soft cloth moistened with a small

amount of water.

2. The main unit is not resistant to heat. Do not place it near a

source of high heat.

3. Do not store the instrument in a place where it may be

subjected to excessive vibrations or from where it may fall.

4. For storing the instrument, avoid hot, cold or humid places or

places under direct sunlight or where condensation is anticipated.

5. When the instrument is not to be used for a long period, be

sure to remove batteries from it.

Following the above instructions, store the instrument in good

environment.

6-4 Battery Replacement

1. If the battery lid is removed with input applied to the input

terminals or in the middle of measurement, you may get

electrical shock. Before starting the work, always make

sure that no input is applied.

2. Before starting the work, ensure that the function switch is

set to OFF.

　　

CAUTION

WARNING

«
...
17
18
19
20
21
...
»

Содержание mg5000





























Отзывы:

Нет отзывов