Samyung SUPERTRACK SDA-390 Скачать руководство пользователя

Страница: 17 / 68

2.7. Cable Connection

For the SuperTrack SDA-390 to work, you must connect the RF cables to your

satellite TV receiver(s). Each RF cable must be an RF (75 ohms) cable fitted with F-

type connectors. The RF cables should already be connected to the antenna base

plate. There should be one ~ four coax cables routed from the ACU to the Antenna

unit according to your configurations. Note that Data and Power are transmitted

through a single coax cable. This cable should be connected to the RF4/ACU

labeled “RF connector of the antenna base plate” and the connector of the ACU

labeled “ANTENNA.” The remaining coax cable routing depends on your

configuration. Due to the signal polarization of the satellites, it is possible for the

SuperTrack SDA-390 to support more than two satellite TV receivers aboard a boat.

To install more than two satellite TV receivers/TV pairs, an active multi-switch is

placed between the Antenna Unit and the Satellite TV receivers. The following

sections provide details for the installation of both a single satellite TV receiver and

multiple satellite TV receivers.

To connect the SuperTrack SDA-390 to your satellite TV receiver(s), choose one of

the following configurations (based on the number of satellite TV receivers you will

connect to the antenna):

Option 1 - Connecting one satellite TV receiver for one satellite

Option 2 - Connecting multi satellite TV receivers

Connecting one satellite TV receiver for one satellite (Only use the ‘HH’

polarity of the satellite)

One satellite TV receiver for one satellite is the simplest type of cable installation.

Only two coaxial cables should be connected between the antenna unit and the

satellite TV receiver, as shown in Figure 2-14. One end of the RF cable should already

be connected to the connector labeled “RF4” on the base of the SuperTrack SDA-390

antenna. Connect the other end of the RECEIVER cable to the satellite TV receiver

connector labeled “LNB,” “ANT/SAT,” or “satellite IN.” And, the “RF4/ACU” connector of

the antenna base plate must also be connected to the “ANTENNA” connector of the

ACU. In this configuration, every satellite should be selected manually using the ACU.

NOTE: Before you connect an RF cable to a satellite TV receiver, turn on the satellite

Содержание SUPERTRACK SDA-390





































































Результаты поиска

Содержание SUPERTRACK SDA-390

Отзывы:

Похожие инструкции для SUPERTRACK SDA-390

Бренды по названию

Популярные бренды

Samyung SUPERTRACK SDA-390, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SUPERTRACK SDA-390

Отзывы:

Похожие инструкции для SUPERTRACK SDA-390

Бренды по названию

Популярные бренды