Samsung RC090MHXEA Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 52

Samsung RC090MHXEA Скачать руководство пользователя страница 20

www.freedomhp.co.uk

©G Hendra Nov 18

20

E177 emergency stop

The mim control box pcb is faulty.

E203

E203 is caused by the inverter board not being connected
to the main PCB in the outdoor unit. The fault will be
displayed on the outdoor unit, the compressor will not run.

To fix the error TURN OFF THE POWER and wait 2 mins
before touching anything. Check the comms cable to the
inverter board, it is a grey cable with 6 cores, it goes from
the right hand side of the main pcb to the top left of the
inverter pcb, the inverter pcb is shown here. If one or
other of the plugs is not connected, plug it in and that
should clear the fault.

When operating correctly the inverter PCB
should have 3 leds showing, the

red

one at the

front will be on, the

green

one below it will be

flashing and a

green

led in the middle of the

board will be lit. If not the PCB is faulty.

When the comms is faulty or the pcb is broken,
the

red

led at the front will be on, the

green

one

below it will NOT be flashing and a

green

led in

the middle of the board will be lit. if this is the
case the pcb (inverter) is faulty.

The inverter pcb can fail due to either the fan motors or the compressors being faulty.
If the fan motor (or motors) or the compressor is faulty they can burn out the inverter
pcb.

You should test the components individually before connecting them to the new
inverter PBC.

See tests:
E467 for compressors
E475 for fan motors
E464 if you want to test the inverter and replacing the board

«
...
18
19
20
21
22
...
»

Содержание RC090MHXEA





















































Отзывы:

Нет отзывов