Samson TROVIS 5724-8 Скачать руководство пользователя

Страница: 10 / 64

EB 5724-8 EN

Safety instructions and measures

1.3

Notes on possible property damage

NOTICE

Risk of actuator damage due to the supply voltage exceeding the permissible

tolerances.

The electric actuators are designed for use according to regulations for low-voltage in-
stallations.

Observe the permissible tolerances of the supply voltage.

Risk of actuator damage due to excessively high tightening torques.

The connection of the electric actuator must be tightened with certain torques. Excessive
tightening torques lead to parts wearing out more quickly.

Observe the specified tightening torques.

The display does not work due to an interrupted cable connection.

The cable connection for the display is located underneath the front housing cover.

Only open the front housing cover to perform actions described in these instructions.

Do not disconnect the connecting cable between the actuator and housing cover.

Malfunction due to a configuration that does not meet the requirements of the

application.

The electric actuator with process controller is configured for the specific application by
setting configuration items and parameters.

Perform the configuration for the specific application during start-up and after a re

set to default settings.

Manipulation of settings at the electric actuator with process controller due to

unauthorized access.

The electric actuator with process controller has a communication interface for data

transmission with the TROVIS-VIEW software (firmware 1.1x: Bluetooth

, firm

ware 2.1x: Modbus RTU). The communication interface is active in the delivered state of

the electric actuator with process controller.

When data transmission is not used, deactivate the communication interface with
the operating keys or by setting the 'Protocol' parameter to 'None'.

Содержание TROVIS 5724-8

































































Результаты поиска

Содержание TROVIS 5724-8

Отзывы:

Похожие инструкции для TROVIS 5724-8

Бренды по названию

Популярные бренды

Samson TROVIS 5724-8, Монтаж и эксплуатация

Результаты поиска

Содержание TROVIS 5724-8

Отзывы:

Похожие инструкции для TROVIS 5724-8

Бренды по названию

Популярные бренды