manualshive.com logo in svg

Salamander Pumps RP100PT, Инструкция по установке и гарантийный талон, Страница: 5 / 29

Поделиться
Скачать
Salamander Pumps RP100PT Скачать руководство пользователя страница 5

2

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Pre-installation checklist

Our pre-installation guidelines are detailed on the following pages, but some of the key 
“do’s and don’ts” are highlighted below:

Do’s

   Locate the pump next to the hot water 

cylinder OR no further than 4m away in 

22mm pipe work

   Allow 100mm on all sides for ventilation
   Ensure pump is protected from frost
   If servicing two or more bathrooms, cold 

water supply to the cylinder must be in 

28mm pipe work

   Ensure adequate cold water storage  

(50 gallons/bathroom, 80 gallons for 

one bathroom and one en-suite)

   Cold water supplies to the pump must 

be taken from the opposite side of the 

cold water storage tank to the cold 

water mains inlet

   Multiple cold water storage tanks must 

be linked in 28mm pipe work and the 

bottom of the tanks must be at the  

same level

   Hot water supply to the pump must be 

via a Salamander approved flange

   AV couplers must only be finger tight 

plus one quarter turn

   The maximum static head should be  

10m (equivalent to 100kPa/1.0 bar 

pressure) – only exception is the 

RP50TU which is 5m (equivalent to 

50kPa/0.5 bar pressure)

   We recommend the pump is activated 

for at least 5 minutes every 4 weeks 

Don’ts

    Never fit the pump to the cold  

water mains

   Never fit the pump to communal risers
   Never use a shared water supply
   Never put a non-return valve (NRV), 

inverted loop, restrictive balofix or an 

air vent on supply pipe work to the pump

   The hot water supply to the pump must 

not exceed 60ºC

    Never twist the anti-vibration (AV) 

couplers or bend more than 35º

   Never use mechanical tools to tighten 

coupler nuts as this may cause damage 

and will invalidate your warranty

    Never use jointing compounds,  

Boss White, Hemp or steel wool

    Solder fluxes must not come into 

contact with the pump or AV couplers

   Never install in a bathroom unless in 

an enclosed space and access is only 

possible with an appropriate tool

   Never pump directly to or from another 

pump

   Never connect to a secondary return 

tapping on a hot water cylinder

BEFORE INSTALLATION OF YOUR NEGATIVE HEAD 

PUMP:

Please fit the pressure vessel if packaged seperate 

to the pump.  Use the 

½ “ flat rubber washer in the 

½ “ brass connection on the top of the pump junction 

box. Screw the pressure vessel into the connection hand 

tight. 

Содержание RP100PT






























Отзывы:

Нет отзывов