manualshive.com logo in svg

Salamander Pumps RP100PT, Инструкция по установке и гарантийный талон, Страница: 27 / 29

Поделиться
Скачать
Salamander Pumps RP100PT Скачать руководство пользователя страница 27

24

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

To the installer

Please follow the guidelines for installation 

provided in this brochure and call the 

PumpWise helpline for installation advice.  

Once installation has been completed and the 

system has been tested to your satisfaction, 

please assist the customer in completing the 

prepaid Warranty Card. 

Terms, conditions and war ranty

1   The Scope of the Warranty

SALAMANDER PUMPED SHOWER SYSTEMS LTD 

(“the company”) Warrants subject to the terms and 

conditions below for the Warranty period(s) specified 

in paragraph 3 that the Company shall:
Repair or replace free of charge the product(s) 

specified on the Warranty card or any component 

part thereof (together referred to as “the equipment”) 

which shall in the opinion of the Company have proved 

defective by reason only of the Company’s materials 

or workmanship providing always that the Company 

shall be under no obligation whatsoever under this 

Warranty to repair or replace equipment which have 

been misused, tampered with, modified/altered in any 

way without the consent in writing of the Company or if 

any component or accessory shall have been replaced 

by a type not specified by the Company or if the 

equipment is incorrectly installed or operated or used 

other than as described in the instruction manual or if 

any servicing or repair of the equipment shall have been 

carried out otherwise than by an authorised Company 

dealer appointed by the Company (“dealer”).
The Company’s liability under this Warranty is limited 

to the said repairs or replacement and shall under no 

circumstances extend to any financial loss or damage 

including consequential losses alleged to have been 

suffered by the claimant.
Subject as provided in this warranty and except where 

the equipment is sold to a person dealing as a consumer 

all warranties, conditions or other terms implied by law 

are excluded to the fullest extent permitted by law.
Nothing in this warranty shall exclude liability for death 

or personal injury caused by the Company’s negligence

2   Terms and conditions

This Warranty shall only be enforceable by you if the 

following terms and conditions have been complied 

with:
a   That the pump has been installed in accordance with 

the installation instructions, guidance and advice 

contained within the installation and warranty guide 

and/or provided by the Salamander  help desk.

b  You are the original purchaser of the equipment from 

a dealer and not an assignee or subsequent purchaser  

of the equipment.

c   You must evidence the date of purchase by retaining 

the original invoice from the dealer. Without such 

evidence the Company reserves the right to reject 

any such claims under the terms of this Warranty.

d  Within 15 days of delivery of the equipment to you 

the Warranty card is accurately completed and 

returned to the Company.

e   Within 30 days of discovery of a defect giving rise 

to liability under paragraph 1 above you give notice 

thereof in writing to the Company.

f   Provided the pump has not been altered, tampered 

with, modified or transformed in any way.

3   The Warranty periods

The Warranty periods referred to in paragraph 1 above 

are as follows:
a   Products manufactured by the Company 2 years 

from date of purchase provided the warranty card is 

completed and returned to the Company within  

15 days of purchase.

b  Products supplied by the company, but are not of the 

company’s manufacture come with 30 day warranty 

from date of purchase. Anti-Vibration Couplers 

(hoses) come with 1 year from date of purchase. 

c   The warranty period in respect of any product 

repaired or replaced under the warranty shall be part 

of the above period(s) which remain unexpired.

d   In the event of a claim for repairs or replacement 

being made under the terms of this Warranty, a 

visit from a Salamander service engineer may be 

necessary. Engineer visits are not covered under/

part of the warranty agreement. In circumstances 

where in the opinion of the Company the defect 

has not been caused by the Company’s materials or 

workmanship, then the Company reserves the right 

to charge the claimant at its current hourly rates 

and list prices in respect of any service engineer’s 

time and replacement of any parts. Please speak to 

our Technical Support team for further details and 

confirmation of costs.

e   This Warranty is given in addition to and does not 

affect your statutory rights as a consumer.

f   This Warranty is valid and enforceable for equipment 

purchased and used exclusively within the UK and the 

Republic of Ireland only.

g   Where the Company issues a replacement the 

equipment replaced shall be returned to the 

Company forthwith and shall become the property of 

the Company.

Содержание RP100PT






























Отзывы:

Нет отзывов