manualshive.com logo in svg

Salamander Pumps RP100PT, Инструкция по установке и гарантийный талон, Страница: 26 / 29

Поделиться
Скачать
Salamander Pumps RP100PT Скачать руководство пользователя страница 26

23

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Monday to Thursday 8.30am to 5.30pm 

Friday 8.30am to 5.00pm.

PumpWise is the cornerstone of 

Salamander’s support service to customers 

and the means by which our customers are 

guaranteed: 
•  Selection of the right pump for the job
  –   With more than 30 pumps in our range, 

the PumpWise team can help you to 

choose the pump that’s most suitable 

to your specific installation 

•  The avoidance of installation pitfalls
  –   Due to the technical nature of our 

products, it is essential that they are 

fitted according to our installation 

guidelines. The PumpWise team 

are available to talk through any 

installation questions and provide 

technical support and guidance.

•  A third year’s warranty FREE
  –   All of our right pumps  come with a 

full two year warranty, but following 

installation of your new pump, if your 

installer calls our PumpWise team, 

registers your pump and runs through 

the system installation you may be 

eligible for a third years warranty 

free.

Our PumpWise commitment

Our PumpWise helpline is here to help you 

and we aim to provide a support service 

second to none. Installers and customers 

can be sure of a speedy response to 

requests for technical help, guidance and 

advice.

Your warranty

Salamander customers benefit from a full 

two year warranty on the Right pump range.

This warranty will operate from the date of 

purchase and is subject to the installation 

guidelines being followed correctly (please 

refer to our Pre-Installation Checklist, on 

page 2 and our Commissioning Checklist, on 

page 11). This warranty could be increased 

free of charge, if the installer contacts our 

Pumpwise team on 0191 516 2002 at the 

time of initial installation, to register the 

pump and run through the installation with 

our Technical Team. Providing the pump has 

been installed according to our guidelines, 

you will receive a third year’s warranty free 

of charge (UK only).
Please complete and return the attached 

warranty card.

Extended warranties

In addition to the three year warranty 

available free of charge following the 

successful installation of your pump, 

there is an optional Extended Warranty 

Scheme (UK only). The Extended Warranty 

Scheme exists to protect customers 

from any unexpected or unforeseen 

pump breakdowns. Participation in the 

Extended Warranty Scheme is activated 

by completion of an Extended Warranty 

Application Form and the payment of a 

nominal fee.
For further details please contact the 

PumpWise team: 

Telephone:  0191 516 2002
Fax:    

0191 548 4445

Email: [email protected]

PLEASE NOTE: Incorrect installation may 

invalidate the pump warranty.  

and warranty

Содержание RP100PT






























Отзывы:

Нет отзывов