Salamander Pumps RP100PT Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 29

Salamander Pumps RP100PT Скачать руководство пользователя страница 14

11

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Commissioning

Before you finish

• Flush inlet pipework and carefully fill

pump with water by discharging water

from the outlet flexible coupler into a

container.

• Fit pump inlet filters.

It is CRITICAL to discharge water through

the pump into a container using natural

flow before connecting the pump to outlet

pipework in order to ensure the air has

been discharged from inlet pipework and

pump chambers. This will not happen if the

outlet pipework is connected to the pump.

The best method is:-

Figure 19

• DO NOT RUN PUMP DRY – to do so will

cause irreparable damage to your pump

and will invalidate your warranty.

• Open shower mixer valve/system

outlets to maximum hot and cold to

check the natural flow (unpumped) flow

of at least 1 litre per minute – positive

head systems.

• Open hot water outlets fully for

5 to 6 seconds and then turn outlets off.

Then open cold water outlets fully for

5 to 6 seconds and turn outlets off. If

flow is poor and inconsistent repeat

above steps until flow is steady.

• Repeat 2-3 times.

MAX

65°C

C

H

The hot connection

must be via an approved

side or top entry flange

except for CT 50/75 and NP 50

OLD STYLE DO NOT USED

Fig 16 Critical

MAX

60˚C

H

C

The hot connection

must be via an approved

side or top entry flange

!

!

• Connect discharge pipework.

• Check that all the pump isolating valves

are open.

• Fill system. Check for leaks.

«
...
12
13
14
15
16
...
»

Содержание RP100PT






























Отзывы:

Нет отзывов