manualshive.com logo in svg

Salamander Pumps RP100PT, Инструкция по установке и гарантийный талон, Страница: 17 / 29

Поделиться
Скачать
Salamander Pumps RP100PT Скачать руководство пользователя страница 17

14

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Helpful

                         

guidelines

Water starvation protection, pipework arrangements and stored hot 

water 

Water starvation protection

In systems where it is absolutely not 

possible to increase the usable cold water 

storage capacity to meet the increased 

demand of a pumped system; a water 

starvation protection unit (WSP) may be 

considered.
The WSP is a Salamander level switch which 

must be positioned 102mm higher than the 

highest outlet from the cold water storage 

tank. When the water level drops too far the 

WSP will switch off the pump until the cold 

water storage level is recovered.

102mm

Outlets

Water starvation

protection unit (WSP)

4 inches

Outlets

WSP

OLD STYLE DO NOT USED

Fig 22 Water starvation

Figure 25: Water starvation protection unit 

(WSP)

Shower head size vs bar pressure

The size of a shower head dictates the bar 

pressure of the pump required to deliver 

the expected performance of the shower.

Shower head diameter

Bar pressure

Up to 5cm

1.5 bar (150 kPa)

5-10cm

2.0 bar (200 kPa)

10-12.5cm

2.5 bar (250 kPa)

More than 12.5cm

3.0 bar (300 kPa)

Anti-gravity loops

An anti-gravity loop (AGL) must always 

be fitted to systems where the pump is 

positioned above the hot outlet from the 

cylinder. The AGL which limits aeration 

of the hot supply to the pump is formed 

by bending the pipework downwards for 

250mm, as it exits the Essex Flange, before 

rising again to the pump. See Figure 26 

overleaf.

Please be advised due to lack of cold water 

storage with Elson and Fortic (type) tanks, 

our pumps may not be suitable.  

It is advisable to contact our Technical 

Support team before installing the pump  

on 0191 516 2002, otherwise it may  

affect your warranty.

Содержание RP100PT






























Отзывы:

Нет отзывов