manualshive.com logo in svg

Salamander Pumps RP100PT, Инструкция по установке и гарантийный талон, Страница: 21 / 29

Поделиться
Скачать
Salamander Pumps RP100PT Скачать руководство пользователя страница 21

18

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

General specification

Applications

All Salamander pumps are designed to 

boost low pressure hot and cold supplies 

from tank-fed services. 

Voltage

220-240 volts 50 Hz.

Motor type

Capacitor start and run induction type 

motor with stainless steel shaft and in-built 

resetting thermal protection (complies 

with BS5000 part 11).

Pump materials

All moulded components are manufactured 

from Acetal Copolymer.

Maximum head

RP 50 TU and RP 55 SU                  5 metres
All other pumps 

10  metres

Pumps fitted with RCM3 maximum 3 

metres static head. 

Pump noise

With the technological advances achieved 

in Right pumps, Salamander has taken 

another step forward in the quest to 

supply all our customers with even quieter 

centrifugal pumps. Despite this no pump is 

completely silent. 
Correct installation will minimise vibration 

and transmission noise. 

Patents

Our Right range of pumps is protected 

by following patent: Hydraulic Pump - 

GB2402444

Mechanical seals

Scale deposits in water supplies can cause 

the mechanical seal to stick if left for long 

periods without use. We recommend the 

pump be ran at least five minutes every  

four weeks to ‘exercise’ all working parts.

Connections

3⁄4” BSP male.

Initiation

Fully automatic, flow switch operated, 

requiring 1 litre in 30 sec per side  or  

2 litre in 30 sec mixed. Except Right 

Universal pumps when required to operate 

in negative  

head mode.

Temperature

Maximum fluid temperature 60ºC.

Standards and approvals

Splash proof rating IPX2.
Complies with the requirements of current 

British and European safety standards for 

household and similar electrical appliances.
Complies with European Community 

Directives (CE).
The company operate a policy of 

continuous development and reserves the 

right to change any of the specifications 

of its products without prior notice. All 

information data and illustrations given in 

this leaflet may be subject to variation.

Содержание RP100PT






























Отзывы:

Нет отзывов