manualshive.com logo in svg

Sakura Tissue-Tek TEC 6, Инструкция по эксплуатации

Поделиться
Скачать
Sakura Tissue-Tek TEC 6 Скачать руководство пользователя страница 33

2. Installation

33

2.1 Installation

2.1.1 General Information on Installing the Instrument

This section provides information on determining a location for, and installing 
the instrument.
Installation should be performed by staff trained in the instrument. This 
instrument must be installed correctly to ensure proper operation and service.
Read this Operating Manual carefully before operating the instrument. Follow 
all instructions provided in this document carefully.

CAUTION
  This instrument is a precision instrument and must be 

handled with care. If the instrument is handled in a rough 

manner or dropped, its internal components may malfunction 

or get damaged. Always exercise due care when handling the 

instrument.

2.1.2 Installation Environment

Install the instrument in a location meeting the following conditions:

•  Free from fire or ignition sources nearby
•  Not exposed to direct sunlight
•  A horizontal level and stable surface area
•  Subject to minimum vibration
•  Protected from water splashes
•  Away from volatile substances or flammable materials 
•  Away from corrosive chemicals (acids, alkalis, etc.)
•  Free from equipment that consumes high voltage or large current 

Example) Large refrigerator, ultrasonic cleaner, cooling centrifuge, etc.

•  The ambient temperature and humidity meet the following use 

environment values:

 

Ambient temperature:  10 to 35°C 

 

Relative humidity: 

30 to 85% (non-condensing)

 

CAUTION

Содержание Tissue-Tek TEC 6









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды